CYC MOTOR DS103 E-Bike Display User Guide

: September 27, 2024
: CYC Motor

Table of Contents

CYC MOTOR DS103 E-Bike Display
Features
Installation
Compatibility
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CYC MOTOR DS103 E-Bike Display

Product Details

Intelligent LCD, model: DS103
Firmware: CYC MOTOR LTD specific firmware

Features

Simple and lightweight, separate installation bracket design
High brightness, high contrast 3.5 colored TFT screen
Clock function (clock is on when the display shutdown)
Excellent outdoor design with IP65-level waterproof
Micro USB serial communication port, convenient maintenance services

Dimensions & Materials

Materials

Product shell – ABS + PC plastic
Transparent window – Tempered glass
Dimensions
L 72mm x W 14mm x H 90.6mm

Electrical Specifications

Power supply: DC 36V/ 48V/ 52V/ 72V
Rated current: 30ma/36V
Shutdown leakage current: <1uA
Screen specification: 3.5” colored TFT (480*320 pixels)
Communication method: UART (default)
Operating temperature: -20°C ~ 60°C
Storage temperature: -30°C~80°C
Waterproof level: IP65

Quick Start Guide
After unboxing and installing your CYC motor system, there are two main things you need to set up.

Change your Battery No. Settings according to your rated voltage. Upon startup, long press the MENU button within 15 seconds to access the SETTINGS page. Press UP/DOWN to navigate the settings page & MENU to select.
Change your Wheel settings according to your bike’s wheel size.
You can now set up parameters like temperature and the speed unit as well as the backlight!

Functionalities
Press and hold the POWER button for 3 seconds to turn the display on/ off.

Navigation
The MENU button is used to go into your main settings page & your clear data page. It is also used to enter and select a setting or function.

Settings
Upon startup, long press the MENU button within 15 seconds to enter the SETTINGS page. Note that once the system is activated for longer than 15 seconds, the motor system will require a restart to enter the settings menu.

Clean Trip Data
Wait 15 seconds after starting up the motor system to enter the “Clean Data” menu. Long pressthe MODE button to clear previous trip data. Please note that trip data does not automatically clear once the motor system is restarted. It is a manual process.

Trip Mode
Upon startup, long press the MENU button within 15 seconds to access the SETTINGS page, then select TRIP MODE to swap between STREET and RACE mode.

Switch Dashboard
Switch the main dashboard to display different information by pressing the MENU button.

Assist Levels Select
Press the UP/DOWN button to change between assist levels while riding. Note that “OFF” means no motor assistance will be given.

There are 3 sets of assist levels; 3, 5 & 9. To change the assist levels set, long press the MENU button within 15 seconds upon startup and access ALL GEAR on the main settings page.

The power output will be distributed evenly across the chosen number of assist levels (or gears) according to the Assist Level Configuration and Speed Limit Assist settings on your Modes & Levels Page on the CYC Ride Control App.

Dark & Light Theme
Upon startup, long press the MENU button within 15 seconds to access the SETTINGS page, then select THEME to change between light and dark-themed dashboards.

Walk Assist
Hold the DOWN button to activate the walk assist. Please note it takes 3 seconds to activate & will deactivate immediately when the button is released.

Error Codes
In certain circumstances, an error code may appear on your display. Contact us for assistance.

Installation

Determine if you need to select the corresponding mounting clamp and rubber clip ring according to the diameter of your handlebar (Applicable handlebar specifications: Φ22.2; Φ25.4; Φ31.8).
Open the display lock clamp and insert the rubber clip (if applicable) into the correct position of the lock clamp.
Set the rubber ring in the bracket (if applicable) then assemble on the middle of the handlebar. You can adjust the angle of the display to make the display screen more visible when riding. After fixing the angle, tighten the screws. The tightening torque is 1N.m.
Open the lock ring of the switch and set it in the appropriate position on the left side of the handlebar. Adjust the angle and position of the switch as needed to ensure the switch can be operated easily.
Fix and tighten the handlebar fixing screw with the M3 Hex wrench (locking torque is 0.8N.m.)
Note: Damage caused by excessive torque is not covered by warranty.