CYC MOTOR DS103 Intelligent LCD Display User Guide
- June 13, 2024
- CYC Motor
Table of Contents
- DS103 Display User Guide
- Features
- Dimensions & Materials
- Materials
- Dimensions
- Electrical Specifications
- Functionalities
- Navigation
- Switch Dashboard
- Assist Level Operating
- Dark & Light Themed Dashboard
- Settings
- Clean Trip Data
- Installation
- Pin Layout
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
DS103 DISPLAY
User Guide
DS103 Display User Guide
Product Details
Intelligent LCD display, model: DS103
Firmware: CYCMOTOR LTD specific firmware
Features
- Simple and lightweight, separate installation bracket design
- High brightness, high contrast 3.5 coloured TFT screen
- Clock function (clock is on when the display shutdown)
- Excellent outdoor design with IP65 level waterproof
- Micro USB serial communication port, convenient maintenance services
Dimensions & Materials
Materials
Product shell – ABS + PC plastic
Transparent window – Tempered glass
Dimensions
L 72mm x W 14mm x H 90.6mm
Electrical Specifications
- Power supply: DC 24V/ 36V/ 48V/ 52V
- Rated current: 30ma/36V
- Shutdown leakage current: <1uA
- Screen specification: 3.5” coloured TFT (480*320 pixels)
- Communication method: UART (default)
- Operating temperature: -20°C ~ 60°C
- Storage temperature: -30°C~80°C
- Waterproof level: IP65
Quick Start Guide
After unboxing and installing your CYC motor system, there are two main things
you need to set up.
- Change your Battery No. settings according to your rated voltage.
Within 15 seconds of turning on your display, long press the MENU button to enter the settings functions. Press UP/DOWN to navigate the settings page & MENU to select.
6s = 22.2V| 9s = 33.3V| 12s = 44.4 V
---|---|---
7s = 25.9V| 10s = 36V| 13s = 48V
8s = 29.6V| 11s = 40.7V| 14s = 52V
Please note that 6s is not compatible with the CYC systems. This will be removed in future batches. Our apologies for the confusion.
- Change your Wheel settings according to your bike’s wheel size.
- You can now set up parameters like temperature and the speed unit as well as the brightness level!
Functionalities
Press and hold the POWER button for 3 seconds to turn the display on/ off.
Navigation
The MENU button is used to go into your main settings page & your clear data page. It is also used to enter and select a setting or function.
Switch Dashboard
Switch the main dashboard to display different information by pressing the
MODE button. 
Assist Level Operating
Press the UP/DOWN button to change the assist level between level 1, 2, and 3.
Note that “OFF” means no motor assistance will be given. 
Dark & Light Themed Dashboard
Long press the UP button to switch between the light and dark themed
dashboards. 
Walk Assist
Hold in the DOWN button to activate walk assist. Please note it takes 3
seconds to activate & will deactivate immediately when the button is released.
Settings
Long press the MODE button within 15 seconds of switching on the display to
enter the “Settings” page. Please note that once the system has been activated
for longer than 15 seconds, the motor system will require a restart to enter
the settings menu. 
Clean Trip Data
Wait 15 seconds after starting up the motor system to enter the “Clean Data”
menu. Long press the MODE button to clear previous trip data. Please note that
trip data does not automatically clear once the motor system is restarted. It
is a manual process. Error Codes
In certain circumstances, an error code may appear on your display. Contact us
for assistance.
Error Code on App & DS103 Display
Controller Over Voltage
Controller Under Voltage
Controller Over Temperature
Hall Sensor Error
Throttle Error
Speed Sensor Error
Controller Internal Error 1
Controller Internal Error 2
Controller Internal Error 3
Controller Internal Error 4
Controller Internal Error 5
Controller Internal Error 6
Controller Internal Error 7
Controller Internal Error 8
Controller Internal Error 9
Controller Internal Error 10
Installation
- Determine if you need to select the corresponding mounting clamp and rubber clip ring according to the diameter of your handlebar (Applicable handlebar specifications: Φ22.2; Φ25.4; Φ31.8).
- Open the display lock clamp and insert the rubber clip (if applicable) into the correct position of the lock clamp.
- Set the rubber ring in the bracket (if applicable) then assemble on the middle of the handlebar. You can adjust the angle of the display to make the display screen more visible when riding. After fixing the angle, tighten the screws. The tightening torque is 1N.m.
- Open lock ring of the switch and set in the appropriate position on the left side of the handlebar. Adjust the angle and position of the switch as needed in order to ensure the switch can be operated easily.
- Fix and tighten the handlebar fixing screw with the M3 Hex wrench (locking torque is 0.8N.m.)
Note: Damage caused by excessive torque is not covered by warranty.
Compatibility
The clamps are suitable for 3x different handlebar sizes: 31.8mm, 25.4mm &
22.2mm.
Pin Layout
Male 5-Pin Connector
- Red Wire: Anode (36V to 72V)
- Black Wire: GND
- Yellow Wire: TxD (display -> controller)
- Green Wire: RxD (controller -> display)
- Blue wire: Power cord to the controller
Certification
CE / IP65 (waterproof) / ROHS
Be sure to contact us if further assistance is needed. Thank you!
© 2023 CYCMOTOR LTD
support@cycmotor.com
+952 3690 8938
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>