SiLION SIM7200 UHF High-Power Module User Manual
- June 12, 2024
- SiLION
Table of Contents
**SIM7200 User Manual
SIM7200
User Manual
Rev 1
**
A revision history
The file number| The version number| Artificial person / The modifier|
Proposed/revis ed date| Change the reason| Change the content
---|---|---|---|---|---
| V1.0| | 2021-10-16| The initial release| No
Product introduction
The UHF high-power module SIM7200 is a high-performance UHF RFID read-write module developed by the technology team of Xinliangzhan based on the new generation of IMPINJ RF chip E710. It is specially designed to meet the requirements of high-performance RFID handheld devices, mobile or portable RFID devices. The SIM7200 module provides one MMCX antenna interface, supporting up to 33 dBm RF output. This module has the characteristics of low power consumption, small size and high sensitivity. Combined with the advanced multi tag algorithm of Xinliangzhan, it is a priority for RFID mobile devices.
Product features
New generation E710 RF chip
Impinj new generation E710 UHF RF reader chip is adopted, which has high
sensitivity, wide reading range, low power consumption and strong performance.
Super tag reading performance
The tag reading speed is fast, the reading is stable, the multi tag anti-
collision ability is strong, and the reading distance is long. When using the
4dBi four wall spiral antenna, the reading distance is more than 9 meters, and
the multi tag reading speed is fast, up to 900 pieces/second.
Lower power consumption
It can work normally in the 3.6V low voltage mode. The maximum power output
power consumption is 6.5W, and the standby power consumption is only 0.25W.
The excellent low power consumption design makes the product have a longer
service life.
Multiple monitoring functions and excellent stability
The module supports label RSSI detection, antenna connection status detection,
and working temperature detection. Multiple data detection is more convenient
for users to use efficiently; The module can work stably in the ambient
temperature of -20℃ to+65℃, and supports stable operation in the ambient
humidity of 5% – 95%. It has high efficiency and stable performance and can be
applied to a variety of harsh working environments.
Electrical characteristics
| parameter | conditions | min | type | max | unit |
|---|
Frequency
Frequency range| According Customization| 840| | 960| MHz
Frequency step value| According Customization| | 250/500| | KHz
output
output power| | 5| | 33| dBin
Output power accuracy| | | +/- 1| | dB
Flatness of output power| | | +/- 0.2| | dB
Channel isolation| | | 32| | dB
label
Reception sensitivity| Profilel| | -81| | dl3m
Inventory label peak
speed| | | 900| | tag/s
Label cache| 96 bit EPC| | 1000| 1200| tag
Logic level
VIL, Input Low Voltage| | -1.| | 0.8| V
V1H, Input High Voltage| | 2| | Vdd+0.5| V
Temperature range
Storage temperature| | -40| | 85| ℃
Working temperature| | -20| | 65| ℃
The input power
The power supply voltage| | 4.| 5.0| 5.| V
Can make model| | | 40| | mA
Standby mode| | | 50| | mA
Read the card model| Pout=30dBm, 50 0 Load| | 1300| | mA
The current will vary depending on the load antenna.
Absolute maximum rated parameter
| parameter | rating |
|---|---|
| power supply voltage | +5V |
| Digital I/O Voltage to GND | 3.3V |
| Working temperature | -20 ~ +65℃ |
| Storage temperature | -40 ~ +85℃ |
Pin configuration and function description
5.1 Definition of FPC connector
| The serial number | define |
|---|---|
| 1 | VCC(+3.6 – 5V) |
| 2 | VCC(+3.6 – 5V) |
| 3 | GND |
| 4 | GND |
| 5 | EN module power enable：LOW(POWER DOWN) HIGH&DISCONNECT(ACTIVE) |
| 6 | Digital Output 2 （GPIO OUT2） |
| 7 | Digital Input 1 （GPIO IN1） |
| 8 | Digital Input 2 （GPIO IN2） |
| 9 | RXD (DATA INPUT，TTL level) |
| 10 | TXD (DATA OUTPUT，TTL level) |
| 11 | RST (LOW ACTIVE，Please hang in the air if not used) |
| 12 | Digital Output 1 （GPIO OUT1） |
5.2 Definition of bottom welding point
| The serial number | define |
|---|---|
| 1 | GND |
| 2 | GND |
| 3 | VCC(+3.6 – 5V) |
| 4 | VCC(+3.6 – 5V) |
| 5 | EN module power enable：LOW(POWER DOWN) HIGH&DISCONNECT(ACTIVE) |
| 6 | RXD (DATA INPUT，TTL level) |
| 7 | TXD (DATA OUTPUT，TTL level) |
| 8 | RST (LOW ACTIVE，Please hang in the air if not used) |
| 9 | Digital Output 1 （GPIO OUT1） |
The application of information
The input power
It is recommended to filter the VCC port with a capacitance of 100~470uF to
reduce the traction to the power supply caused by the quick opening and
closing of the power amplifier during RF tran smission. 0.1uF/100pF capacitors
filter out power supply ripple in different frequency bands. Since the current
is high when the module is working at full power, the module may not work sta
bly when the battery is low when the handheld device is powered directly by
the battery, so it is r ecommended to boost the VCC to 5V.
Enable or reset EN is enabled, with built-in pull-up resistance (100k) to VCC.
When the module is powered on at high level or suspended, the module will be
powered off when it is connected to low level (low leve l should be less than
0.4V, high level should be greater than 0.9V and less than VCC).
Rst reset, built-in pull-up resistance to 3.3V, reset when connected to low
level.
GPIO interface
Input:
Logic low ＜ 0.8V minimum 0V
Logic high ＞2 V Maximum 3.3 V
Output:
Logic Low maximum 0.4V
Logic High has a minimum of 2.9V and a maximum of 3.3V
The maximum output current of the I/o port is 5mA.
The antenna connection
The output impedance of the antenna port is 50 ohms, and the antenna standing
wave ratio is rec ommended to be less than 1.5. A better antenna standing wave
ratio can get better card reading effect.
Communication interface (rxd/txd)
The communication interfaces RXD and TXD are at TTL level, and the default
baud rate is 115200b ps
Physical properties
Product size：74.8mm × 48.5mm × 8mm
weight：56g
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. Any Changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance 30cm
between the radiator & your body.
Beijing Xinlian Chuangzhan
Electronic Technology Co., LTD
Tel:（+86）010-62153842/62153840
http://www.silion.com.cn
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>