TECNO CAMON 30 5G Smartphone User Manual
- September 25, 2024
- TECNO
Table of Contents
TECNO CAMON 30 5G Smartphone
Explosion diagram specification
1 | LCD ASSY | 2 | PDN shielding cover mylar |
---|---|---|---|
3 | Main board RF_PA shielding cover copper foil | 4 | Back secondary camera |
5 | Back main camera | 6 | FPC for receiver and speaker |
7 | Front cover ASSY | 8 | Front camera |
9 | Top waterproof membrane | 10 | CPS module |
11 | Main board copper foil (Bottom) | 12 | Light sensor rubber sleeve |
13 | Top waterproof foam | 14 | Main board copper foil (Bottom) |
15 | RF Cable | 16 | Grounding copper foil for main camera BTB connector |
17 | Screw | 18 | Adhesive for upper speaker |
19 | Middle frame thermal rib | 20 | Middle frame ASSY |
21 | Decorative parts for battery cover | 22 | Adhesive for back camera lens |
23 | Glass battery cover ASSY | 24 | Camera Lens |
25 | Sealing foam for back acoustic cavity | 26 | Main FPC |
27 | SIDEKEY_FPC ASSY | 28 | Main camera grounding copper foil |
29 | SIM socket copper foil | 30 | RF cable Homonymous |
31 | Front cover ASSY | 32 | Bottom speaker double layer heat sink |
33 | Back secondary camera ASSY | 34 | Battery wrapping film |
35 | Speaker FPC ASSY | 36 | Main board BB shielding cover copper foil |
37 | Polymer Lithium-ion Battery | 38 | Type-C sealing silicone sleeve |
39 | SIM socket | 40 | Middle frame ASSY |
41 | Metal decorative parts | 42 | Sealing adhesive for metal decorative parts on |
battery cover
43| Glass battery covary ASSY| 44| Round head screw
Know your phone
- Front camera
- Volume + key
- Volume – key
- Power key
- Earphone jack
- USB port
- Breathing Light
- Camera
- NFC
SIM card installation
Charging the phone
You can charge your device using a charger or by connecting it to the computer
using a USB cable (comes with the phone).
Use only TECNO charger and cables. Other chargers or cables may damage the
device. This will invalidate your phone warranty.
FCC Caution
Labelling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Information to user.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This mobile phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6W/kg averaged over one gram of tissue. Device types: CL7s(FCC ID: 2ADYY- CL7S) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0.60 W/kg and when properly worn on the body is 0.69 W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 1.0 cm must be
maintained between the user’s body and the handset, including the antenna.
Third-party belt-clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do not
meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or an approved antenna.
HiOS runs on AndroidTM OS.
Android is a trademark of Google LLC
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>