AcuityBrands ARUE3 Post Top LED Lantern Lights Instruction Manual

: June 5, 2024
: AcuityBrands

Table of Contents

AcuityBrands ARUE3 Post Top LED Lantern Lights
IMPORTANT SAFETY INSTRUCTIONS
INTRODUCTION
INSTALLATION
Install house side shield with tabs over optic
Limited Warranty and Limitation of Liability
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AcuityBrands ARUE3 Post Top LED Lantern Lights

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.
Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
Installation and service of luminaires should be performed by a qualified licensed electrician.
Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards involved. Regular fixture maintenance programs are recommended.
It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.
DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
If the lamp is marked (Hg) it contains Mercury. Follow all disposal laws. See www.lamprecycle.org.
These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.

WARNING
RISK OF ELECTRIC SHOCK

Disconnect or turn off power before installation or servicing.
Verify that supply voltage is correct by comparing it with the luminaire label information.
Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
All wiring connections should be capped with UL approved recognized wire connectors.

RISK OF BURN

Allow lamp/fixture to cool before handling. Do not touch hot lens, lamp, guard, or enclosure.
Do not exceed maximum wattage marked on luminaire label.
Follow all lamp manufacturer’s warnings, recommendations and restrictions on lamp operation including but not limited to: ballast type, burning position, replacement, and recycling.
Use only lamps that comply with ANSI standards.

CAUTION
RISK OF INJURY

Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
Avoid direct eye exposure to the light source while it is on.

RISK OF FIRE

Keep combustible and other materials that can burn away from lamp/lens.
Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.

Failure to follow any of these instructions could void product warranties.
For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com.

INTRODUCTION

These instructions are intended to guide field installation of the 90, 120 and 180 degree house side shield for the Taft, Arlington, and Jefferson LED product line.

INSTALLATION

Tools and Materials Required.
¼” socket or nut driver (ARE3, ARUE3, JFE3, JFUE3, and PTUE3 cover) 3/8” Nut driver (PTE3 cover)

Remove the luminaire cover. Disconnect the main power quick-disconnect and photo control circuit (if applicable) and remove LED heat sink assembly and support on a clean horizontal work surface. See Figures 1 & 2.

Install house side shield with tabs over optic

See Figure 3.
Orient the house side shield on the optic so it shields the light from the object you want shielded.

Re-install LED heat sink assembly by orienting “latch” on heat sink with “street side” on optic. See Figures 4, 5, & 6.

Replace the luminaire cover.

Limited Warranty and Limitation of Liability

The Holophane limited warranty and limitation of liability is published in the “Terms and Conditions” section of the current Holophane buyer’s guide, and is available from your local Holophane sales representative. 3825 Columbus Rd., Granville, OH 43023IN-364 10/23 ©2017 Acuity
Brands Lighting, Inc.
All Rights Reserved.
Visit our web site at www.holophane.com