Eastbrook 33.0014 Freestanding Bath with Claw Feet Instructions
- September 24, 2024
- Eastbrook
Table of Contents
Eastbrook 33.0014 Freestanding Bath with Claw Feet
Receive Your Bath
Unpack and check for damage.
After receiving your bath, please unpack and remove all packaging, checking
for damage. Repack the bath if it is not being immediately installed. Metal
bars required for feet installation are attached to the underside of the bath.
Metal Feet do NOT come with the bath and must be Purchased Separately.
Protect your bath
Before commencing installation, ensure the bath is completely protected, leave
covering in place until the bathroom is complete. Scratches and damage
incurred during installation are not covered by the Eastbrook.
Important information
- Two people are required for installation.
- Freestanding bath is not designed to take weight on the rim.
- Do not sit or stand on the bath rim.
Spare Parts
| Part No. | Part Description | Qty (pcs) | Image |
|---|
Part 1 – Metal Bar Box (Bars attached to underside of bath rim)
A| Metal Bar-187mm| 4|
Part 2 – Metal Feet Box (NOT come with the bath and must be Purchased
Separately)
B| Bolt| 4|
C| Nut| 4 (pre-assembled on the feet)|
D| Washer| 4|
E| Fastener washer| 4|
F| Adjustable feet| 4|
Part 3- Pre-assembled on the underside of the bath
C| Nut| 8|
D| Washer| 8|
TOOLS REQUIRED
| Adjustable Wrench
---|---
Installation
Step 1
-
Ensure the bath is on a soft surface to protect against scratches.
-
Take off the plastic covers of screws and unscrew nuts and washers from the bath(these are pre-assembled on bath). See Figure 1
-
Place the metal bars onto the bath, along with the washers and nuts as shown below, do not tighten at this stage to allow for adjustment, taking care not to damage the bath surface. See Figure 2
Step 2
-
Position the feet on the bar, fasten with washers, fastener washers and bolts, but not tighten the bolts right away. See Figure 3
-
Adjust the position of the feet to align with the bath, metal bars could be adjusted if needed. See Figure 4
-
Tighten all of the nuts so that the feet are secured to the metal bar and the metal bars are secured to the bath. See Figure 5
Step 3
Assemble the overflow and waste (not supplied with the bath).
Connect the bath trap (not supplied with the bath) to the fitted bath waste
and connect that to the bathrooms’ waste pipes.
Step 4
Place the bath to the desired location and water test the bath for any leaks
before use.
Troubleshooting
Movement or noise on the feet after assembly
Please check if the feet are assembled properly, make sure fastener washers
and washers are placed correctly.
Maintenance & Cleaning
a. Marks on the surface of the bath, should be cleaned using a soft damp
cloth, for more stubborn marks, toothpaste can be applied and then rinsed
thoroughly.
b. No harsh cleaning chemicals or abrasive materials can be used on any
surface.
If using coloured oils/creams, carry out a test on small area prior to use to
ensure that these will not cause staining.
c. Never pour coloured oils/creams directly into an empty bath, always
apply them into the bath water.
WARNING
Pay attention to below points if the bath is designed with tap deck.
a. The tap holes are not pre-drilled on the deck, drill holes according
to your need.
b. Check and silicone the tap holes to make sure the reinforcement layer
is still solid after drilling.
c. Check and make sure that there is no water leakage at the faucet.
Customer Support
Technical Helpline: 01452 317890
Email: technical@eastbrookco.com
Eastbrook Road, Gloucester GL4 3DB
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>