Eastbrook 880-900 Walk In Panels Installation Guide

Eastbrook 880-900 Walk In Panels

Specifications

Product: Valiant and Volente Walk-in Panels
Sizes Available: 880-900, 985-1000, 1180-1200, 680-700, 740-760, 780-800, 480-500

Product Usage Instructions

Tools Required

• Pencil
• Drill bit (6.3mm)
• Silicone gun
• Flat and cross screwdriver
• Tape measure
• Spirit level
• Electric drill
• Rubber hammer

List of Spare Parts

• X1 A
• X1 B
• X1 C
• X1 D
• X1 E
• X2 F
• X1 G
• X4 ST4*12 H
• X6 J
• X6 ST4*30 K
• X2 L

Installation Steps

1. Dry fit the panels to determine the best position for the wall profile.
2. Drill holes and fit wall plugs or hollow wall fixings as needed.
3. Screw wall profile A to the wall using ST4*30 K screws.
4. Fit the panel into the wall profile.
5. Drill guide holes into the profile attached to the glass panel using a 3.2mm drill bit and secure with washers and screws provided.
6. Choose the position for the wall support bar, cut it to the correct length, and attach brackets D & E.
7. Fit the support bar wall bracket E in the required position.
8. Check all screws for proper securement.
9. Fit wall profile corner caps G and F using silicone sealant on the outside only.

Cleaning & Maintenance
Do not clean the shower enclosure with irritant detergents like alcohol, bleach, or other chemical cleaners. Only use warm soapy water for cleaning.

FAQ
Q: What should I do if I notice missing parts or damage?
A: Report any missing parts or damage to your supplier within 10 days of purchase and before installation to ensure timely resolution.

INSTALLATION MANUAL

VALIANT AND VOLENTE WALK IN PANELS

This product should only be fitted by a fully qualified installer.

• This product must be unpacked and checked for quality prior to installation.
• Any missing parts or damage must be reported to your supplier within 10 days of purchase and before installation.
• No claims can be enforced outside of these terms.

TOOLS REQUIRED

LIST OF SPARE PARTS

Please make the following checks before connecting the installation:

• The product supplied is the required size and the adjustment is compatible with the site situation.
• Check all component parts are present, see packing list and product schematic diagram for reference.
• Make sure you have all the required tools.

PRODUCT SCHEMATIC DIAGRAM

1. Dry fit required for best position to connect wall profile.

2. Drill holes and fit wall plugs if a solid wall substitute for hollow wall fixings if necessary (not supplied).

3. Screw wall profile A to wall with ST4*30 K screws.

4. Fit panel into wall profile.

5. Drill guide holes into profile attached to glass panel with 3.2mm drill bit through existing holes in wall profile at chosen adjustment and secure with washer I and ST4*12 H screws provided.
   Push screw cover profile B onto washers.

6. Choose required position for wall support bar.

7. Cut bar C to correct length. Separate wall brackets D and E into component parts and attach to bar C with screws provided.

8. Attach brackets D & E to bar ensuring D is in the correct position, and fix with the screws supplied.

9. Fit support bar wall bracket E in the position required with ST4*30 K screws provided. Substitute wall plugs J for hollow wall fixings if necessary.

10. Connect bar C to wall bracket E with screw provided. Attached glass clamp D to panel with screws provided. Check all screws are secured correctly.

11. Fit wall profile corner caps G and F .

12. Silicone as illustrated ensures silicone sealant is on the outside only.

13. Silicone as illustrated ensuring silicone sealant is on the outside only.

Cleaning & Maintenance

• Don’t clean the shower enclosure with irritant detergent such as alcohol,bleach or other chemical cleaners.
• Only clean with warm soapy water .
• Helpline:01452 317890

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>