Eastbrook Valiant and Volente Walk in Panels Installation Guide
- July 30, 2024
- Eastbrook
Table of Contents
Valiant and Volente Walk in Panels
“`html
Specifications
- Product: Valiant and Volente Walk-in Panels
- Available Sizes: 880-900, 985-1000, 1180-1200, 680-700,
740-760, 780-800, 480-500
Product Usage Instructions
Tools Required
- Pencil
- Drill bit (6.3mm)
- Silicone gun
- Flat and cross screwdriver
- Tape measure
- Spirit level
- Electric drill
- Rubber hammer
List of Spare Parts
- X1 A
- X1 B
- X1 C
- X1 D
- X1 E
- X2 F
- X1 G
- X4 ST4*12 H screws
- X4 ST4*30 K screws
- X6 ST4*12 J screws
- X2 L screws
Installation Steps
Cleaning & Maintenance
Do not use irritant detergents like alcohol or bleach for
cleaning. Clean only with warm soapy water.
Contact Information
Helpline: 01452 317890
FAQ
Q: Can I install the panels myself?
A: This product should only be fitted by a fully qualified
installer to ensure proper installation and safety.
Q: What should I do if I notice missing parts or damage?
A: Any missing parts or damage must be reported to your supplier
within 10 days of purchase and before installation.
“`
VALIANT AND VOLENTE WALK IN PANELS
880-900 985-1000 1180-1200 680-700 740-760 780-800 480-500
660-680 720-740 760-780 860-880 960-980 480-500
This product should only be fitted by a fully qualified installer.
This product must be unpacked and checked for quality prior to installation. Any missing parts or damage must be reported to your supplier within 10 days of purchase and before installation. No claims can be enforced outside of these terms.
TOOLS REQUIRED
c
Pencil
( 63. 2) Drill bit
Silicone gun
Flat and cross screwdriver
Tape measure
Spirit level
Electric drill
Rubber hammer
LIST OF SPARE PARTS
X1
A
B X1
X1
C
D
X1
E
X1
(L)(R)
F X2
X1
G
ST4*12
X4
H
X4
I
J X6
ST4*30
ST4*12
K X6
L X2
Please make the following checks before connecting the installation: The product supplied is the required size and the adjustment is compatible with the site situation. Check all component parts are present, see packing list and product schematic diagram for reference. Make sure you have all the required tools. (1)
PRODUCT SCHEMATIC DIAGRAM
(2)
1
Dry fit required for best position to connect wall profile.
A
2
Drill holes and fit wall plugs if a solid wall substitute for hollow wall
fixings if necessary (not supplied).
6mm
J
3
Screw wall profile A to wall with ST4*30 K screws.
4
Fit panel into wall profile.
K
(3)
5 Drill guide holes into profile attached to glass panel with 3.2mm drill bit
through existing holes in wall profile at chosen adjustment and secure with
washer I and ST4*12 H screws provided. Push screw cover profile B onto
washers.
1
3.2mm
H
2
I
3
B
Choose required position for wall support bar.
A
B
(4)
Cut bar C to correct length. Separate wall bracket D and E into component parts and attach to bar C with screws provided.
Attach brackets D & E to bar ensuring D is in the correct position, and fix with screws supplied.
Fit support bar wall bracket E in position required with ST4*30 K screws provided.
Substitute wall plugs J for hollow wall fixings if necessary.
E
6mm
J
K
1
2
3
4
5
1
2
3
4
Connect bar C to wall bracket
E with screw provided.
Attached glass clamp D to
panel with screws provided.
(5)
Check all screws are secured correctly.
12
Silicone gun
Fit wall profile cover caps G and F .
Silicone as illustrated ensuring silicone sealant is on the outside only.
13
Silicone gun
gun Silicone
Silicone as illustrated ensuring silicone sealant is on the outside only. (6)
Cleaning & Maintenance
Don’t clean the shower enclosure with irritant detergent such as
alcohol,bleach or other chemical cleaners. Only clean with warm soapy water .
Helpline:01452 317890
(7)
S-277
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>