BORMANN PRO BDM6600 062257 60m Laser Distance Meter Instruction Manual

BORMANN PRO BDM6600 062257 60m Laser Distance Meter

Product Information

Specifications

• Model: BDM6600
• Measuring Range Accuracy: Measuring units: m, in, ft
• Laser Type: Class II, 620-690 nm

Product Usage Instructions

Safety Instructions

Warning: Read the manual carefully before use. Failure to follow the warnings and instructions may result in product damage and/or physical injury. Store the manual in a safe place for future reference.

Important Information

It is crucial to follow the safety instructions provided in the manual to ensure proper and safe usage of the product. Always refer back to the manual for guidance and reference.

How to Use

1. Ensure you have read and understood all safety instructions.
2. Power on the BDM6600 device using the designated power button.
3. Select the desired measuring unit (m, in, ft) on the device.
4. Aim the laser at the target surface you wish to measure.
5. Read and record the measurement displayed on the device screen.
6. Power off the device after use to conserve battery.
7. Store the device in a safe and dry place.

FAQ

• Q: What should I do if the measurement readings seem inaccurate?
  • A: Ensure that the laser is properly aimed at the target surface and that there are no obstructions interfering with the measurement process. If issues persist, refer to the troubleshooting section in the manual or contact customer support.
• Q: Can the BDM6600 be used outdoors?
  • A: Yes, the BDM6600 can be used outdoors, but ensure that environmental conditions such as bright sunlight do not affect the accuracy of the laser measurements.
• Q: How do I change the batteries in the BDM6600?
  • A: Refer to the manual for detailed instructions on how to safely replace the batteries in the BDM6600 device. Always use recommended battery types for optimal performance.

SAFETY INSTRUCTIONS

Warning: Read the manual carefully before use. Failure to follow the warnings and instructions may result in product damage and/or physical injury. Store the manual in a safe place for future reference.

• This is a class Il laser product. Do not stare into the beam at any time when operating this product.
• Do not look directly into the beam with optical aids (e.g binoculars, telescopes).
• Do not remove any safety labels from the product.
• Do not allow children to use the product.
• Do not open the product.
• Do not modify the equipment in any way.

IMPORTANT INFORMATION

• When measuring, do not point the laser directly at the sun.
• Do not immerse the product in water.
• Do not clean the lens using alcohol or any other organic solvent.
• Do not wipe the lens with fingers or objects with rough surfaces.
• Do not power the equipment beyond the rated DC voltage.

TECHNICAL SPECIFICATIONS

• The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
• Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.

LCD SCREEN INDICATIONS

• Laser indication.
• Measurement reference.
• Continuous measurement.
• Area/volume measurement.
• Pythagoras measurement.
• Error indication.
• Battery capacity indication.
• Max and min indication.
• Data storage.
• Unit indication.
• Angle indication.
• Current measurement.
• Calculation display.

BUTTONS

Battery installation (Fig. 2)

Caution:

• Do not mix new and old batteries. Use alkaline or rechargeable batteries only.
• Replace the batteries when the symbol flashes permanently in the display.
• Remove the batteries before any long period of non-use.

1. Remove the battery compartment lid.
2. Insert the batteries, making sure the polarity is correct by observing the battery lid indications.
3. Close the battery compartment lid.

Switching on (Fig. 3)

• Press the button to switch on the equipment.

Changing the measurement reference (Fig. 3-5)

• The default measuring reference is the bottom of the meter. (Fig. 3)
• Press the button to set the top of the meter as the measuring reference. (Fig. 4)
• Press the button. The laser indication as well as the battery capacity indication will be displayed. (Fig. 5)

Switching off

• Press and hold the button to switch off the equipment.
• The laser will be switched off automatically after 30 seconds and the equipment will be powered off after 3 minutes, provided no button is pressed.

Clear button

• Press the button to clear the last command or displayed data, one type of data at a time.

Measurement

Single-mode measurement (Fig. 6)

• When the equipment is switched on, press the button to activate the laser, then aim the laser on the target and press again to trigger single-mode measurement.
• The measurement will be displayed immediately on the screen. (Fig. 6)

Continuous-mode measurement (Fig. 7-8)

• When the equipment is switched on, press and hold the continuous-mode measurement.
  • MIN: Minimum value.
  • MAX: Maximum value.
• The current measurement value will be displayed on the screen. (Fig. 8) button to trigger

Functions

Area – Volume – Indirect measurement (Pythagorean theorem) (Fig. 9-11)

• When the equipment is switched on, press the button to switch measurement functions.
  • Area measurement: Figure 9.
  • Volume measurement: Figure 10.
  • Indirect measurement (Pythagorean theorem): Figure 11.
• Select the desired measurement function and start measuring. (See table B)

Storage and recall of measurements

• Storage of measurements: press the button to view the stored measurements.
• Press the + or – button to switch from one stored measurement to another.
• Plus and minus functions (Fig. 12-13)
  • When the equipment is in single measurement mode, press +. The meter can calculate the last measurement and the current measurement.
  • Press -. The meter can calculate the last measurement minus the current measurement.

TROUBLESHOOTING

ENVIRONMENTAL DISPOSAL

In order to avoid damages on transportation, the tool has to be delivered in solid packaging. Packaging as well as the unit and accessories are made of recyclable materials and can be disposed accordingly. The tool’s plastics components are marked according to their material, which makes it possible to remove environmentally friendly and differentiated because of available collection facilities.

Only for EU countries

Do not dispose of electric tools together with household waste material! In observance of European Directive 2002/96/EC on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

WWW.NIKOLAOUTOOLS.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>