HYPERCEL 15166 True Wireless Earbuds User Manual

HYPERCEL 15166 True Wireless Earbuds

IMPORTANT

Read all safety instructions and warnings prior to using this product. Improper use and failure to follow safety guidelines could result in damage, excess heat, toxic fumes, fire, explosion, electrical shock or other hazards causing serious and/or fatal injury and/or property damage and not the manufacturer’s responsibility. The user is responsible for maintaining this product with care for maximum use.

1. Do not store the device in a depleted state. Battery cells may be damaged. Charge your unit at least once every 3 months even when not in use
2. Always store the earbuds in the case when not in use.
3. Permanent hearing loss may occur if you listen at high volumes. Set the volume to a safe level.
4. Do not store at extreme temperatures (below 40For above 90 F)
5. Recharge your device with the included Micro USB charging cable or a certified 3rd party cable and a 2A charging adapter. Standard cables and adapters may charge the battery too slowly and damage/overheat the battery or cause a fire hazard.
6. Do not attempt to modify, disassemble, or repair this product.
7. Avoid excessive drops, bumps, and abrasions.
8. If the device has dents, punctures, tears, deformities, or corrosion, discontinue use and contact the manufacturer or dispose of in an appropriate method.
9. If you find this product rapidly increasing in temperature, emitting odor, deformed, abraded, or demonstrating an abnormal phenomenon, discontinue use immediately.

Contact info@myhypergear.com to submit a warranty claim. Proof of purchase is required.

INSTRUCTIONS

Fully charge your Case and Earbuds before first use.

1. Place the earbuds in the charaing case
2. Connect to a USB power source using the included Micro USB charging cable
3. Once plugged in, the case LED will flash RED
4. When charging is complete, the LED will turn off (approximately 2 hours)

Charge the Earbuds

1. Place the earbuds in the charging case. Press the power button on the case to turn the charaer ON
2. The case LED will turn BLUE
3. When charging is complete, the LED will turn off (approximately 1 hour)

Getting Started

Power On

• Option 1: Remove the earbuds from the charging case. They will automatically turn on
• Option 2: Press the MFB on BOTH earbuds at the same time for 4 seconds. They will turn on automatically.

Power Off

• Option 1: Place the earbuds in the charging case and close the lid They will automatically turn off.
• Option 2: Press the MFB on BOTH earbuds at the same time for 4 seconds. They will turn off automatically.

How to Pair

1. Remove the earbuds from the charaing case

2. They will turn on and pair with each other automatically.

3. Wait for the RIGHT (R) earbud to flash RED& BLUE

4. Activate the Bluetooth feature on your device (phone, tablet, etc.) and select “HyperGear True Wireless” to connect and pair.
   NOTE: If vour device promnts for a PIN code enter u0000″

5. You will hear a tone confirming the successful connection
   NOTE: The earbuds will automatically reconnect to the last paired Bluetooth audio device when the unit is turned on.

MULTIFUNCTION!

• Play/Pause Press lx
• Answer/End Call
• Reject call Prass & Hold (3 sec)
• Redial Last Number Press 2x

TRACK CONTROL

• (L) Left Earbud
  Previous Track Long Press (2 sec)

• R) Right Earbud
  Next Track Long Press (2 sec)

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Need help? Visit www.myhypergear.com for additional product information or email info@myhypergear.com

References

• HyperGear | Phone Accessories, Bluetooth, Wireless Chargers, TWS – HYPERGEAR

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>