PNI SVM-10K,PNI SVT-10K Voltage Stabilizer Instructions
- September 27, 2024
- PNI
Table of Contents
PNI SVM-10K,PNI SVT-10K Voltage Stabilizer Instructions
High-accuracy Full-automatic AC Voltage Stabilizer
1. General
1.1 The voltage stabilizers PNI SVM-10K and PNI SVT-10K are designed to stabilize the output voltage. When the input voltage from the electrical network fluctuates, the voltage stabilizer will automatically adjust the voltage as close as possible to the preset value.These stabilizers have high capacity, high efficiency, no waveform distortion and automatic voltage regulation, so that the connected devices can work correctly. PNI servo motor voltage stabilizers have a wide range of applications. Depending on their capacity, they can connect: electric mechanical equipment, industrial equipment, air conditioners, televisions, household appliances, electric tools, refrigerators and, in general, electronics that need stable voltage.
2. Model description
SVM-10K: single-phase high-accuracy full-automatic AC voltage stabilizer
- Input Voltage
- Output Voltage
- Normal functionality
- Overvoltage
- Undervoltage
- General protection switch
SVT-10K: three-phase high-accuracy full-automatic AC voltage stabilizer
- Output Voltage
- Normal functionality
- Overvoltage
- Undervoltage
- General protection switch
- Phase voltage display switch
2.1 Main technical parameters
2.3 Curve of output capacity (see below diagram )
2.4 Circuit diagram
2.4.1 Circuit diagram of single-phase high-accuracy full-automatic AC voltage stabilizer of 0.5kVA~10kVA (see below diagram )
2.4.2 Circuit diagram of three-phase high-accuracy full-automatic AC voltage stabilizer (see below diagram )
3 Operating instruction
Voltage stabilizers are only used indoors, taking into account the following requirements:
- Operating temperature: -26°C ~ +80°C
- Altitude: < 1000 m above sea level
- Humidity: ≤ 90%
- There must be no gases, vapors, chemicals or explosive substances, excess dust, excess humidity in the work space.
- The surface on which the stabilizer is installed must be flat, without vibrations.
- For installation under special conditions, ask for specialist advice.
3.1 The output power indicated on the voltage stabilizer that is the max power, and the nominal power of household appliance refers to the active power, the power of inductive loads such as refrigerator, air conditioner, etc. shall be multiplied by 3 to 5 times, because they have high current at the starting moment. If the input voltage is too low, the load shall be reduced.
3.2 The supply voltage shall be in the range of nominal input voltage, when output voltage is in the state of over voltage, the “over voltage” indicator lamp of voltage stabilizer will go on, at this moment, the voltage stabilizer can cut off the output voltage automatically to ensure the safety of power device.
3.3 When user uses the motor or other starting equipment of high current, please select voltage stabilizer with capacity of above 3 times, in order that the equipment can work smoothly not affected by large voltage drop of circuit for too high starting current.
3.4 Three-phase voltage stabilizer must be connected with neutral wire that forms three-phase four-wire system, only that, it can work normally, but the neutral wire can’t be taken the place of earth wire.
3.5 To ensure the device and human safety, the enclosure of voltage stabilizer is mounted with grounding screw or grounding terminal, user must connect the grounding wire properly.
3.6 After finishing installing, please turn on the input power switch, in case that the operation indicator lamp goes on, and the output voltage is in the normal range, user can turn on the electrical appliance to let the load run normally.
Maintenance
To ensure operation in optimal conditions for a long period of time, follow the following instructions:
- do not block the ventilation slots of the stabilizer
- periodically clean the stabilizer housing of dust
- check the input and output cables if they are correctly connected and if they are in good condition
- check that the stabilizer does not have condensation on the housing.
Table 1 Common symptom and remedy
In case of improper operation of the voltage stabilizer, before calling a specialized service center, check the following:
- check the power cable of the stabilizer and the power cable of the device connected to the stabilizer.
- check the starting power of the device connected to the stabilizer. It is recommended that this does not exceed 80% of the nominal power of the stabilizer. If it exceeds this threshold for a long time, it is recommended to increase the ventilation capacity of the stabilizer.
- If there is a power failure while the stabilizer and the consumers are working, after the power returns, gradually connect the consumers.
EU Simplified Declaration of Conformity
ONLINESHOP SRL declares that Voltage Stabilizer PNI SVM-10K and Three-phase Voltage Stabilizer PNI SVT-10K complies with the Directive EMC 2014/30/EU. The full text of the EU declaration of conformity is available at the following Internet address:
https://www.mypni.eu/products/8248/download/certifications
https://www.mypni.eu/products/8249/download/certifications
CERTIFICATE OF QUALITY AND COMMERCIAL WARRANTY
The products identified in this certificate based on the trade name and the sole series number S/N benefit by a commercial warranty as follows:
The warranty period for natural persons is 24 months as of the delivery date for the manufacturing and material defects.
The warranty period for legal entities is 12 months as of the delivery date for the manufacturing and material defects.
The cables, adaptors, consumables, batteries, accumulators, battery chargers, transformers, microphones, earphones, aerials which are part of the products or are delivered with them shall have a commercial warranty of 6 months as of the date of the product sale to the end consumer. The term of warranty shall be calculated as of the invoicing date of each product individually.
The average term of the product service life is 48 months subject to the compliance with the assembly and operation instructions accompanying the product.
The commercial warranty shall not impair the consumer rights provided by the applicable legislation in force, namely Emergency Government Ordinance 140/28.12.2021 on certain issues related to contracts for the sale of goods, the Government Ordinance 21/1992 on the consumer protection as subsequently amended and supplemented by Law 296/2004 on the consumption code as subsequently amended and supplemented.
Please download the full version of the warranty certificate:
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>