IXL Appliances IW25-5 IN Wall Dehumidifier Installation Guide
- September 18, 2024
- IXL Appliances
Table of Contents
IW25-5 IN Wall Dehumidifier
“`html
Product Information
Specifications:
- Model: IW25-5
- Type: In Wall Dehumidifier Exterior Sleeve
- Exterior Sleeve Dimensions: 445mm W x 775mm H x 56mm D
- Manufacturer: IXL Home Pty Ltd
- Compatibility: Not compatible with IW25-5 ON Wall
Dehumidifier
Product Usage Instructions
Installation:
-
Follow steps 6-8 from the Installation and Operation Manual:
IW25-5 Dehumidifier IN Wall (page 9). -
Once step 8 is complete, there will be a cut out opening to
partially recess the IW25-5 into the cavity wall. Fit the exterior
sleeve against the cut-out opening. Make sure the pop-out for
drain/power are at the bottom of the sleeve. -
Ensure the Exterior Sleeve is level and bottom of the IW25-5
will be supported. Attach Exterior Sleeve with 4 screws (not
provided) directly through the wall into studs. -
Continue to Step 9 of the In Wall installation
instructions. -
In Step 11 of the In Wall installation instructions, use the
four screws (included with the Exterior Sleeve) to attach the
mounting tabs to the Exterior Sleeve. -
Continue installation instructions in the manual from step 12
to finish installation.
Frequently Asked Questions (FAQ)
Q: Is the Exterior Sleeve covered under the IW25-5 Dehumidifier
Warranty?
A: No, the Exterior Sleeve is not covered under the IW25-5
Dehumidifier Warranty.
Q: Is the Exterior Sleeve compatible with the IW25-5 ON Wall
Dehumidifier?
A: No, the Exterior Sleeve is not compatible with the IW25-5 ON
Wall Dehumidifier.
“`
Installation Manual
IW25-5 IN Wall Dehumidifier Exterior Sleeve
Please Read and Save These Instructions
Contact Us:
IXL Home Pty Ltd 1K Marine Parade, Abbotsford, VIC 3067
AUS: 1300 727 421 NZ: 0800 727 421
www.ixlappliances.com.au www.ixlappliances.co.nz
IW25-5 IN Wall Dehumidifier Exterior Sleeve Installation
The IW25-5 In Wall Dehumidifier can be semi-recessed with an Exterior Sleeve for a clean bump out finish, where unit cannot be fully installed into a 90mm stud wall, ideal for retrofit applications.
The Exterior sleeve is not covered under the IW25-5 Dehumidifier Warranty and
is not compatible with the IW25-5 ON Wall Dehumidifier.
Exterior Sleeve Dimensions: 445mm W x 775mm H x 56mm D
Exterior sleeve mounted against wall and firmly secured into a solid surface. (ie timber stud)
IW25-5 In Wall unit with mounting brackets attached to Exterior Sleeve
IW25-5 In Wall Dehumidifier installed with Exterior Sleeve and cover.
368mm
19mm
Figure 1
711mm 19mm
Installation
1. Follow steps 6-8 from the Installation and Operation Manual: IW25-5
Dehumidifier IN Wall (page 9).
2. Once step 8 is complete, there will be a cut out opening to partially
recess the IW25-5 into cavity wall. Fit the exterior sleeve against the cut-
out opening. Make sure the pop-out for drain/power are at the bottom of
sleeve.(Figure 1)
3. Ensure the Exterior Sleeve is level and bottom of the IW25-5 will be
supported. Attach Exterior Sleeve with 4 screws (not provided) directly
through wall into studs.
4. Continue to Step 9 of the In Wall installation instructions.
5. In Step 11 of the In Wall installation instructions, use the four screws
(included with the Exterior Sleeve) to attach the mounting tabs to the
Exterior Sleeve.
6. Continue installation instructions in manual from step 12 to finish
installation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>