TECNO CL7 CAMON 305G Mobile Phone User Manual
- September 23, 2024
- TECNO
Table of Contents
TECNO CL7 CAMON 305G Mobile Phone
Explosion diagram specification
| 1 | LCD ASSY | 2 | PDN shielding cover mylar |
|---|---|---|---|
| 3 | Main board RF PA shielding |
cover copper foil
| 4| Back secondary camera
5| Back main camera| 6| FPC for receiver and speaker
7| Front cover ASSY| 8| Front camera
9| Top waterproof membrane| 10| CPS module
11| Main board copper foil (Bottom)| 12| Light sensor rubber sleeve
13| Top waterproof foam| 14| Main board copper foil (Bottom)
15| RF Cable| 16| Grounding copper foil for
main camera BTB connector
17| Screw| 18| Adhensive for upper speaker
19| Middle frame thermal rib| 20| Middle frame ASSY
21| Decorative parts for battery
cover
| 22| Adhensive for back camera
lens
23| Glass battery cover ASSY| 24| Camera Lens
25| Sealing foam for back acoustic
cavity
| 26| Main FPC
27| SIDEKEY FPC ASSY| 28| Main camera grounding
copper foil
29| SIM socket copper foil| 30| RF cable_Homonymous
31| Front cover ASSY| 32| Bottom speaker double layer
heat sink
33| Back secondary camera ASSY| 34| Battery wrapping film
35| Speaker FPC ASSY| 36| Main board BB shielding
cover copper foil
37| Polymer Lithium-ion Battery| 38| Type-C sealing silicone sleeve
39| SIM socket| 40| Middle frame ASSY
41| Metal decorative parts| 42| Sealing adhensive for metal decorative
parts on battery
cover
43| Glass battery covery ASSY| 44| Round head screw
45| Speaker bracket| 46| mainboard bottom side insulation mylar
47| grounding copper foil for
front camera
| |
Know your phone
- Front camera
- Indicator light
- Volume + button
- Volume – button
- Power button
- NFC
SIM card installation
- Power off mobile.
- Refer to the following picture for SIM card installation.
Charging the phone
- You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone).
- Use only TECNO charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.
FCC
FCC Caution: Labelling requirements.
This device complies with Part 15 of the FCC Rules. Operation 1s subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Information to the user.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, under part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used under the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information
This mobile phone meets the government’s requirements for exposure to radio
waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluation
of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons regardless of age or health.
RF Exposure Information and Statement The SAR limit of the USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: CL7(FCC ID: 2ADYY-CL7) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0.77W/kg and when properly worn on the body is 0. 78 W /kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 1.0 cm must be
maintained between the user’s body and the handset, including the antenna.
Third-party belt clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do not
meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or approved antenna.
HiOS runs on Android™ OS.
Android is a trademark of Google LLC.