ATEN AD004E Series Audio Digital Signal Processor with Dante User Guide
- September 24, 2024
- Aten
Table of Contents
AD004E / AD400E / AD202E
Audio Digital Signal Processor with Dante
Quick Start Guide
© Copyright 2024 ATEN® International Co. Ltd.
ATEN and the ATEN logo are registered trademarks of ATEN International Co.,
Ltd.
All rights reserved. All other trademarks are the property of their respective
owners.
Released: 05/2024
(A) Hardware Overview
AD004E Front View
AD004E Rear View
AD400E Front View
AD400E Rear View
AD202E Front View
AD202E Rear View
(B) Mounting
Rack Mount
Surface Mount
Package Contents
1 AD004E / AD400E / AD202E Audio Digital Signal Processor with Dante
1 rack mount / surface mount kit
1 foot pad set (4 pcs)
5 3-pin Euro blocks
1 user instructions
Support and Documentation Notice
All information, documentation, firmware, software utilities, and
specifications contained in this package are subject to change without prior
notification by the manufacturer.
To reduce the environmental impact of our products, ATEN documentation and
software can be found online at
http://www.aten.com/download/
Technical Support
www.aten.com/support
Scan for more information
Product Page
A Hardware Overview
1 input / output level LEDs
The LED(s) lights green to indicate the amplitude level is more than -50dBu
while it lights red if it reaches the hard-clipping limit (+18dBu).
2 sampling rate LEDs
(a) The LED lights green if the signal sampling rate is at 44.1kHz, and it
lights red if the signal sampling rate is at 88.2kHz.
(b) The LED lights green if the signal sampling rate is at 48kHz, and it
lights red if the signal sampling rate is at 96kHz.
3 standby LED
The LED lights orange when the unit goes into standby mode, and it blinks in
orange if system error occurs.
4 power LED
The LED lights green to indicate the unit is powered on, and it blinks in
green when firmware upgrade is in process.
5 phantom power LEDs
The LED(s) lights orange to indicate the phantom power is on.
6 AEC (acoustic echo cancellation) LED
The LED lights blue to indicate acoustic echo cancellation (AEC) is activated.
7 FBS (feedback suppressor) LED
The LED lights blue to indicate feedback suppressor (FBS) is activated.
8 power jack
Plug the power adapter to the power jack.
9 Dante link / PoE port
Use an Ethernet cable to connect the Dante link port to a network switch. It
is strongly recommended that you use a shielded Cat 5e cable (or higher) for
better network connectivity and preventing EMI (Electromagnetic Interference).
Power over Ethernet (PoE Class 0, IEEE802. 3af) is supported.
10 Dante link port
Use an Ethernet cable to connect the Dante link port to a network switch. It
is strongly recommended that you use a shielded Cat 5e cable (or higher) for
better network connectivity and preventing EMI (Electromagnetic Interference).
11 reset button
Use a paper clip to reset the unit. Insert the point end to press and hold the
button for 5 seconds to reset Dante settings while press and hold the button
for 10 seconds to reset the unit to its factory default settings.
12 RS-232 serial port
A 3-pin RS-232 serial port with Tx, Rx, and GND for connecting to ATEN Control
System.
13 audio line output channels
Connect the audio output devices via balanced or unbalanced audio cables.
14 audio mic / line input channels
Connect the cables from your audio source device to the ports.
(B) Mounting
Note: The foot pad set is used only when placing the unit on a flat surface to prevent the unit from slipping. Do not attach the foot pads to the unit if you’d like to mount the unit onto a system rack or secure it on a flat surface.
Rack Mount
To mount the unit onto a 19″ (1U) system rack:
(1) Using the rack mount kit, attach the 2 mounting brackets onto the
sides of the unit with six M3 indented hex washer head screws provided.
(2) Align the mounting brackets’ screw holes with that of the front of
the rack, and secure the unit onto the rack using self-supplied screws.
(3) For dual rack mount, screw the line bracket onto the bottom side of
the two units with four M3 flat head screws. Attach the mounting brackets onto
the units with six M3 indented hex washer head screws provided. Follow step 2
to secure the unit onto the system rack.
Surface Mount
To secure the unit on a flat surface:
(1) Use four M3 flat head screws to fasten the line brackets to the
bottom of the unit as shown in the diagram above.
(2) Place the unit on a flat surface, such as a desk, and secure the unit
on the surface with self-supplied screws.
Note: Please use the screws that fit 3mm screw hole diameter.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>