ATEN PG98230 3-Phase Intelligent PDU User Guide

ATEN PG98230 3-Phase Intelligent PDU

Hardware Overview

1. power outlets
2. status panel
3. circuit breakers (not applicable to PG98230)
4. power cord
5. outlet status LEDs

Status Panel

1. USB Type-A port (fi rmware upgrade / log export)
2. COM + PON port
3. LAN 1 (10/100/1000M)
4. reset button
5. sensor port
6. LAN 2 (10/100M)
7. LCD panel

Installation

1. Make sure the unit is properly grounded.
   Note: Do not omit this step. Proper grounding helps prevent damage to the unit from power surges or static electricity.

2. For each device you want to connect, use its power cable to connect the device’s AC power inlet to any available outlet on the eco PDU. Use ATEN Lok-U-Plug cable holders to secure them.

3. Connect the unit’s LAN 1 (10/100/1000M) or LAN 2 (10/100M) port to a network using an Ethernet cable. For network redundancy, optionally connect both LAN ports to the network using 2 Ethernet cables.
   Note: You can also use the LAN ports to cascade up to 64 eco PDUs.

4. (Optional) Connect an environmental sensor to the unit’s sensor port.

5. (Optional) Connect an RS-232/RS-485 serial controller to the unit’s COM port.
   Note: You can also use the port as a PON port, connecting to an ATEN KVM over IP Switch via an Ethernet cable.

6. Connect the unit’s built-in power cord to an AC power source, thereby turning it on, and then turn on the connected devices.

Package Contents

• 1 Power Distribution Unit
• 1 rack mount kit
• 1 RJ-45 to DB-9 cable
• 1 full-panel colored sticker
• 1 user instructions

Support and Documentation
Notice All information, documentation, fi rmware, software utilities, and specifi cations contained in this package are subject to change without prior notifi cation by the manufacturer.
To reduce the environmental impact of our products, ATEN documentation and software can be found online at http://www.aten.com/download/

Technical Support
www.aten.com/support

Scan for more information

Rack Mount Lock Positions

When mounting onto a rack, make sure to use the correct screw positions, at the rear of the unit, that correspond to your installation scenario, as explained below:

• T1: Use T1 to mount the eco PDU onto an ATEN rack with its power cord extending toward the top of the rack.
• B1: Use B1 to mount the eco PDU onto an ATEN rack with its power cord extending toward the bottom of the rack.
• T: Use T to mount the eco PDU onto a 3rd-party rack with its power cord extending toward the top of the rack.
• B: Use B to mount the eco PDU onto a 3rd-party rack with its power cord extending toward the bottom of the rack.

Operation
ATEN eco PDU provides 3 methods for managing the unit and its powered devices: browser, eco DC, and SNMP.

Browser

1. Open a browser and specify the IP address of the eco PDU you want to access in the browser’s URL location bar.
   Note: You can get the IP address from the eco PDU administrator, or see the IP Address Determination section of the user manual (default IP address: for non-DHCP: 192.168.0.60 / 192.168.0.61).

2. If a Security Alert dialog box appears, accept the certification — it can be trusted. The login page appears.

3. Provide a valid username and password.
   Note: For first-time login, use the default Username and Password: administrator and password.

4. Then click Login to bring up the browser main page.

eco DC
All ATEN eco PDUs support ATEN eco DC (Energy & DCIM Management Web GUI). eco DC offers an intuitive and user-friendly graphical user interface that allows you to configure eco PDUs and monitor the power status of all equipment connected. ATEN eco DC can be downloaded from our website www.aten.com

SNMP
ATEN eco PDUs support any 3rd-party V1, V2, or V3 SNMP management software. SNMP Management Information Database (MIB) fi les for the eco PDU can be found on the product webpage.

References

• ATEN - Simply Better Connections | ATEN U.S.A.
• Downloads | ATEN Corporate Headquarters

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>