BRESSER 70000 Series Clima Temp Hygro Indicator Instruction Manual
- August 29, 2024
- BRESSER
Table of Contents
BRESSER 70000 Series Clima Temp Hygro Indicator Instruction Manual
ClimaTemp Hygro Indicator
Art. No. 7000010CM3000 / 7000015CM3000
7000010GYE000 / 7000015GYE000
7000010QT5000 / 7000015QT5000
7000010MGU000 / 7000015MGU000
INSTRUCTION MANUAL
GENERAL WARNINGS
RISK OF CHOKING!
Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard.
RISK of ELECTRIC SHOCK!
This device contains electronic components that operate via a power source (Batteries). Only use the device as described in the manual; otherwise, you run the risk of an electric shock.
RISK of FIRE/EXPLOSION!
Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit the device or batteries, or throw them into a fire. Excessive heat or improper handling could trigger a short-circuit, a fire or an explosion.
RISK of property damage!
Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
NOTE!
Do not immerse the unit in water. Do not subject the unit to excessive force, shock, dust, extreme temperature or high humidity, which may result in malfunction, shorter electronic life span, damaged batteries and distorted parts.
NOTE!
Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. Remove the batteries from the unit if it has not been used for a long time.
NOTE!
The manufacturer is not liable for damage related to improperly installed batteries!
EC DECLARATION OF CONFORMITY
Bresser GmbH has issued a “Declaration of Conformity” in accordance with
applicable guidelines and corresponding standards. The full text of the EU
declaration of conformity is available at the following internet address:
www.bresser.de/download/7000010/CE/7000010_CE.pdf
www.bresser.de/download/7000015/CE/7000015_CE.pdf
CLEANING AND MAINTENANCE
Before cleaning the device, disconnect it from the power supply (remove batteries)! Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.
DISPOSAL
Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal. Do not dispose of electronic devices in the household garbage!
As per Directive 2012/19/EU of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.
SCOPE OF DELIVERY
Thermo/Hygro device, instruction manual, button cell battery (3.0V, type CR2032)
PARTS OVERVIEW
❶ Display
(a) Indoor temperature, (b) Indoor humidity, (c) Comfort level
❷ Wall-mount recessed hole
This hole makes it possible to mount the main unit on a wall.
❸ Battery compartment for 1x CR2032
❹ Table stand
Add if station is to be placed on a flat surface.
POWER SUPPLY
- Open the battery compartment door.
- First use: remove the tranparent plastic tab. Battery change: Use only a CR2032 (3.0V) type battery and insert it according to the polarities (+/-) shown.
- Reinsert the battery compartment door.
OPERATION
Temperature and humidity
- Once the battery is installed, the main unit will start displaying the interior measurement information.
- There are 3 different icons to displaying the indoor climate as below:
Comfort level
humidity is lower than 40%; at the same time, the temperature is higher than 20°C, but lower than 27°C.
humidity is higher than 70%, or temperature is lower than 20°C, or temperature is higher than 27°C.
humidity is between 40%-70%, at the same time, the temperature is higher than 20°C, but lower than 27°C.
SPECIFICATIONS
Measurement
Indoor temperature range: 0-50 °C
Temperature tolerance: ± 1 °C
Humidity range: 10-99%
Humidity tolerance: ± 5%
Power supply
1x CR2032 3.0V button cell
WARRANTY & SERVICE
The regular warranty period is 2 years and begins on the day of purchase. To
benefit from an extended voluntary warranty period as stated on the gift box,
registration on our website is required.
You can consult the full warranty terms as well as information on extending
the warranty period and details of our services at
www.bresser.de/warranty_terms.
Bresser GmbH
Gutenbergstraße 2
46414 Rhede · Germany
@BresserEurope
Bresser UK Ltd.
Suite 3G, Eden House,
Enterprise Way • Edenbridge,
Kent TN8 6HF • Great Britain
Errors and technical changes reserved.
Manual_7000010000000_7000015000000_ClimaTemp-Hygro_en-de-fr-es-it-
cs_BRESSER_v082024a
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>