RandG Racing EH0124 Moto Guzzi Stelvio Exhaust Hanger and Blanking Plate Kit Installation Guide

: September 21, 2024
: RandG Racing

Table of Contents

RandG Racing EH0124 Moto Guzzi Stelvio Exhaust Hanger and Blanking Plate
Specifications
FAQs
PRODUCT INFORMATION
TOOLS REQUIRED
PARTS LIST
FITTING INSTRUCTIONS
CONTACT INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RandG Racing EH0124 Moto Guzzi Stelvio Exhaust Hanger and Blanking Plate

Kit

Specifications

Product Name: EH0124 Exhaust Hanger
Manufacturer: R&G Racing
Contents:
- 1 x Exhaust Hanger (HB0119)
- 1 x M8 x 20mm Button Head Bolt
- 1 x M8 Washer
- 1 x M8 Nut
- 2 x M8 x 20mm Countersunk Bolts
Manufacturer Contact: R&G Racing, Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ

FAQs

Q: Can I discard the rubber washers included in the kit?
- A: Yes, if rubber washers are used to hold components onto bolts, they can be thrown away.
Q: Where can I find digital copies of the fitting instructions?
- A: Digital copies of the instructions are available for download on the R&G Racing website at www.rg-racing.com.

PRODUCT INFORMATION

THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER THE PAGE.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
PLEASE READ ALL INSTRUCTIONS BEFORE PRECEEDING.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF MOUNTING THE BIKE.
THE PARTS SHOWN MAY BE REPRESENTATIVE ONLY (FOR CLARITY OF INSTRUCTIONS ONLY).
IN THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS,
THESE RUBBER WASHERS CAN BE THROWN AWAY.
Digital copies of these instructions are available to download from www.rg-racing.com.

TOOLS REQUIRED

Set of metric Allen keys
Torque wrench to suit.

MAXIMUM TORQUE SETTINGS

M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
M12 BOLT = 40Nm

PARTS LIST

LEGEND

ITEM No	DESCRIPTION	QTY
ITEM 1	EXHAUST HANGER (HB0119)	1
ITEM 2	M8 x 20mm BUTTON HEAD BOLT	1
ITEM 3	M8 WASHER	1
ITEM 4	M8 NUT	1
ITEM 5	M8 x 20mm COUNTERSUNK BOLTS	2

FITTING INSTRUCTIONS

To fit the R&G Exhaust Hanger, the OEM pillion footrest mounting bracket needs to be removed.
To do this, remove the two mounting bolts at the top of the pillion footrest mounting bracket, and the one OEM bolt holding the footrest to the exhaust silencer, then remove the OEM pillion footrest mount from the motorcycle.
Take the R&G Exhaust Hanger (Item 1) and fit the two M8 x 20mm long countersunk head bolts (Item 5) through the two top mounts of the exhaust hanger as shown in the assembly picture.
Offer the exhaust bracket into position and engage both bolts into the pillion-foot peg mounting holes (do not fully tighten at this stage).
With the exhaust hanger loosely mounted on the motorcycle, ensure the lower part of the exhaust hanger is on the outside of the exhaust mounting bracket.
Place the M8 button head bolt (Item 2) through the washer (Item 3) & exhaust hanger mounting bracket before fitting the M8 nut (Item 4) onto the exposed thread of the bolt and loosely tighten it as shown in the assembly picture.
Ensure the exhaust hanger is correctly fitted before tightening all three bolts.
Please ensure when the motorcycle is being used that no parts are in such a position that they may collide/damage other bike parts (this is particularly important if using after-market cans or exhaust systems).

Please note that it is your responsibility to ensure that no part of the exhaust hanger or exhaust assembly fouls or comes into contact with other parts of the machine. Do not ride the motorcycle until this aspect has been verified and you have compressed the rear suspension (if appropriate to the design of the motorcycle) to test this thoroughly. Issue 1 – 01/03/2024 (MH)

CONSUMER NOTICE

The catalog description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes.
Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed.
The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products.
On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than per R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect.
Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.

R &G RETURNS POLICY (NON-FAULTY GOODS)

Returns must be pre-authorised (if not pre-authorised the return will be rejected).
Goods may only be returned directly to us if they were purchased directly from us (customer must prove if necessary). Otherwise to be returned to the original vendor. Goods must be in re-sellable condition, in the opinion of R&G.
All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at the time of purchase). The customer must pay all carriage charges. No returns of discontinued products, unless within 14 days of purchase.
This policy does not affect your statutory rights and does not refer to faulty goods.