RandG Racing SP0105 Rear Wheel Sliders Swingarm Owner’s Manual
- September 13, 2024
- RandG Racing
Table of Contents
RandG Racing SP0105 Rear Wheel Sliders Swingarm
FITTING INSTRUCTIONS FOR SP0105 SWINGARM PROTECTORS
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE.
SOME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE
FITTED BY A QUALIFIED TECHNICIAN.
PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE
WAY OF MOUNTING TO THE BIKE.
IN THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS,
THESE RUBBER WASHERS CAN BE THROWN AWAY.
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM: WWW.RG-RACING.COM
TOOLS REQUIRED
- 5mm Allen Key x 2
- Small amount of super glue
| GENERAL TORQUE SETTINGS
- M4 BOLT = 8Nm
- M5 BOLT = 12Nm
- M6 BOLT = 15Nm
- M8 BOLT = 20Nm
- M10 BOLT = 40Nm
- M12 BOLT = 40Nm
---|---
LEGEND
| ITEM NO. | DESCRIPTION | QTY |
|---|---|---|
| ITEM 1 | SB182 SPINDLE BAR | 1 |
| ITEM 2 | S1527 – LHS SPACER | 1 |
| ITEM 3 | S1526 – RHS SPACER | 1 |
| ITEM 4 | B0575 CRASH PROTECTOR | 2 |
| ITEM 5 | M8 BARREL NUT | 2 |
ASSEMBLY DIAGRAM
FITTING INSTRUCTIONS
- To start this fitting process, place one barrel nut (Item 5) onto the end of the spindle bar (Item 1) and tighten until at least half of the spindle bar thread is inside the barrel nut.
- A fitting suggestion: using a small amount of Loctite on the Spindle bar thread will help create an even number of threads on both sides of the swingarm protector once fully tightened.
- Now slide one crash protector bung (Item 4) and RHS Spacer (Item 2) onto the bar in the configuration shown in the ASSEMBLY DIAGRAM.
- Slide the assembly through the RHS of the rear spindle. Once through place the LHS Spacer (Item 3) and remaining crash protector bung (Item 4) onto the end of the spindle bar that’s protruding through the LHS.
- Finally, place the second barrel nut (Item 5) over the exposed end of the spindle bar and tighten with two 5mm Allen keys simultaneously to the correct torque using the GENERAL TORQUE SETTINGS table on PAGE 2.
ISSUE 1 – 14/05/2024 (MH)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad
indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state
shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products
other than those in R&G’s order or confirmation and the Buyer confirms it has
chosen the Products as being of merchantable quality and suitable for its
particular purposes. Where R&G fits the Products or undertakes other services
it shall exercise reasonable skill and care and rectify any fault free of
charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of
the Products. On return of any defective Products R&G shall at its option
either supply a replacement or refund the purchase money but shall not be
liable if the Products have been modified or used or maintained otherwise than
in accordance with R&G’s or manufacturer’s instructions and good engineering
practice or if the defect arises from accident or neglect. Other than
identified above and subject to R&G not limiting its liability for causing
death and personal injury, it shall not be liable for indirect or
consequential loss and otherwise its liability shall be limited to the amounts
paid by the Buyer for the Products or the fitting or service concerned. These
terms do not affect the Buyer’s statutory rights.
R &G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be
rejected). Goods may only be returned direct to us if they were purchased
direct from us (customer must prove if necessary). Otherwise to be returned to
original vendor. Goods must be in re-sellable condition, in the opinion of R&G
Racing. All returns are subject to a 25% restocking and handling fee (25% of
the gross value exc. P&P – at the prevailing price at time of purchase). The
customer must pay any and all carriage charges. No returns of discontinued
products, unless within 14 days of purchase. This policy does not affect your
statutory rights and does not refer to faulty goods.
R &G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007
www.rg-racing.com
Email: info@rg-racing.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>