RandG RACING BE0227 Handlebar End Sliders Installation Guide

: September 21, 2024
: RandG Racing

Table of Contents

RandG RACING BE0227 Handlebar End Sliders
SPECIFICATION
LEGEND
FITTING INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RandG RACING BE0227 Handlebar End Sliders

This Kit contains the items pictured and labeled over the page. Some parts may be shown for clarity of instructions only. Do not proceed until you are sure all parts are present. Please read all instructions before proceeding. IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN. Please note that the way the kit is packed does not necessarily represent the way of mounting the bike. In the event of rubber washers being used to hold components onto bolts, these rubber washers can be thrown away. DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM www.rg- racing.com

SPECIFICATION

TOOLS REQUIRED

· Set of Metric Allen keys.

· 8mm Spanner

| GENERAL TORQUE SETTINGS

M4 BOLT = 8Nm M5 BOLT = 12Nm M6 BOLT = 15Nm M8 BOLT = 20Nm

M10 BOLT = 40Nm

---|---

LEGEND

ITEM No.	DESCRIPTION	QTY
ITEM 1	BAR END (HDPE)	2
ITEM 2	METAL SPACER	2
ITEM 3	M6 x 40mm BOLT	2

FITTING INSTRUCTIONS

Remove the OEM handguard, bar end bolt & bar end, keeping the OEM threaded insert in place.
Place Item 1 & 2 over the threaded insert & thread the M6 bolt (Item 3) through & into the OEM threaded insert.
Repeat for the opposite side & ensure the product is tight and secure before riding.

CONSUMER NOTICE
The catalog description and any exhibition of samples are only broad indications of the Products and R&G may make design changes that do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than by R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.

R &G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned directly to us if they were purchased directly from us (customer must prove if necessary). Otherwise to be returned to the original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at the time of purchase). The customer must pay any carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.

R&G Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com