RandG Racing RAD0342PRO Radiator Guard PRO Owner’s Manual
- September 13, 2024
- RandG Racing
Table of Contents
RandG Racing RAD0342PRO Radiator Guard PRO
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE. SOME PARTS MAY BE
SHOWN FOR CLARITY OF INSTRUCTIONS ONLY.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE
FITTED BY A QUALIFIED TECHNICIAN.
- PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF MOUNTING TO THE BIKE.
- IN THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS, THESE RUBBER WASHERS CAN BE THROWN AWAY.
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
TOOLS REQUIRED
- WIRE CUTTERS
GENERAL TORQUE SETTINGS
- M4 BOLT = 8Nm
- M5 BOLT = 12Nm
- M6 BOLT = 15Nm
- M8 BOLT = 20Nm
- M10 BOLT = 40Nm
- M12 BOLT = 40Nm
LEGEND
| ITEM NO. | DESCRIPTION | QTY |
|---|---|---|
| ITEM 1 | RAD0342 RADIATOR GUARD | 1 |
| ITEM 2 | RUBBER BUNG | 5 |
| ITEM 3 | CT130 RADIATOR TIES (PACK OF 4) | 2 |
FITTING DIAGRAM
FITTING INSTRUCTIONS
-
Remove the LHS & RHS fairing panels to gain access to the front and rear of the radiator
-
To fit R&G radiator guard to the bike, insert the 5x rubber grommets into the radiator guard in the holes circled in YELLOW in the Fitting Diagram if they do not come already installed & slide the R&G Radiator Guard into position. Refer to Picture 1 for the correct orientation.
-
Offer the R&G Radiator Guard into position and secure the radiator guard in place using 6 supplied R&G one-way radiator ties through the holes circled in GREEN in the Assembly Diagram.
Important : Ensure the radiator ties pass through the outer matrix of the radiator and not between the fins as shown in PICTURE 3. -
The locking part of each radiator tie needs to be secured from behind the radiator as shown in Picture 2. Ensure to fit in the correct orientation so the locking section engages the teeth.
-
Check the radiator guard is secure and cut the excess material from the radiator tie.
-
Check tightness regularly and that all ties remain tight in place.
CONSUMER NOTICE
The catalog description and any exhibition of samples are only broad
indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state
shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products
other than those in R&G’s order or confirmation and the Buyer confirms it has
chosen the Products as being of merchantable quality and suitable for its
particular purposes. Where R&G fits the Products or undertakes other services
it shall exercise reasonable skill and care and rectify any fault free of
charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of
the Products. On return of any defective Products R&G shall at its option
either supply a replacement or refund the purchase money but shall not be
liable if the Products have been modified or used or maintained otherwise than
by R&G’s or manufacturer’s instructions and good engineering practice or if
the defect arises from accident or neglect. Other than identified above and
subject to R&G not limiting its liability for causing death and personal
injury, it shall not be liable for indirect or consequential loss and
otherwise its liability shall be limited to the amounts paid by the Buyer for
the Products or the fitting or service concerned. These terms do not affect
the Buyer’s statutory rights.
R &G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be
rejected). Goods may only be returned directly to us if they were purchased
directly from us (customer must prove if necessary). Otherwise to be returned
to the original vendor. Goods must be in re-sellable condition, in the opinion
of R&G Racing. All returns are subject to a 25% restocking and handling fee
(25% of the gross value exc. P&P – at the prevailing price at the time of
purchase). The customer must pay any carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not
affect your statutory rights and does not refer to faulty goods.
R&G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007
Fax : +44 (0)1420 87301 www.rg-racing.com
Email: info@rg-racing.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>