RandG Racing LP0376BK Tail Tidy Installation Guide
- September 13, 2024
- RandG Racing
Table of Contents
RandG Racing LP0376BK Tail Tidy
FITTING INSTRUCTIONS FOR LP0376BK LICENCE PLATE BRACKET
- This kit contains the items pictured and labelled over page.
- Some parts may be shown for clarity of instructions only.
- Do not proceed until you are sure all parts are present.
- Please read all instructions before proceeding.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
Please note that the way the kit is packed does not necessarily represent the
way of mounting to the bike.
In the event of rubber washers being used to hold components onto bolts, these
rubber washers can be thrown away.
R &G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44
(0)1420 89007 www.rg-racing.com Email: info
@rg-racing.com
TOOLS REQUIRED
- Set of metric Hex keys to include 5mm & 6mm.
- Set of metric sockets and wrench. To include 8mm, 10mm & 12mm.
- Cable cutters
| GENERAL TORQUE SETTINGS
M4 BOLT = 8Nm M5 BOLT = 12Nm M6 BOLT = 15Nm M8 BOLT = 20Nm M10 BOLT = 40Nm
M12 BOLT = 40Nm
---|---
LEGEND
| ITEM No. | DESCRIPTION | QTY |
|---|---|---|
| ITEM 1 | MAIN BRACKET | 1 |
| ITEM 2 | NUMBER PLATE LIGHT CONNECTOR | 1 |
| ITEM 3 | RUBBER BUNG | 1 |
| ITEM 4 | 20mm BUTTON HEAD BOLT | 2 |
| ITEM 5 | 25mm BUTTON HEAD BOLT | 2 |
| ITEM 6 | FLAT WASHER | 6 |
| ITEM 7 | NYLOC NUT | 2 |
| ITEM 8 | 75mm CABLE TIE – BLACK | 4 |
| ITEM 10 | 200mm LENGTH OF Ø18mm HEAT SHRINK | 1 |
| ITEM 11 | 200mm LENGTH OF HEAT SHRINK | 1 |
| ITEM 12 | LICENCE PLATE LIGHT (W/SHROUD) | 1 |
| ITEM 13 | 100mm LENGTH OF SELF-ADHESIVE FOAM | 1 |
ASSEMBLY DIAGRAM
FITTING INSTRUCTIONS
Disassembly of OEM Tail Unit
- Disconnect the wiring connector going to the OEM number plate light unit located under the passenger seat.
- Remove the OEM tail unit via the four bolts on the tail unit/ undertray of the motorcycle.
- Once removed, un-screw all visible bolts on the OEM Tail Unit, disassemble the unit, then remove the OEM indicators for later use.
- Also remove the sub-loom for use with the R&G tail tidy.
- Re-assemble the OEM Tail unit without the indicators and store away safely.
Tail Tidy Assembly
- Insert the supplied rubber bung into the 1” hole on the tail tidy bracket.
- If required cut the supplied self-adhesive foam strips to a similar size shown in the assembly diagram above and stick in the position shown.
- Fasten the supplied R&G number plate light to the tail tidy assembly.
- Bolt the OEM indicators onto the tail tidy, using the supplied nyloc nuts and washers with the OEM bolts.
- Insert the supplied rubber bung into the 1” hole on the tail tidy bracket.
- If required cut the supplied self-adhesive foam strips to a similar size shown in the assembly diagram above and stick in the position shown.
- Fasten the supplied R&G number plate light to the tail tidy assembly.
- Bolt the OEM indicators onto the tail tidy, using the supplied nyloc nuts and washers with the OEM bolts.
Please note : It is important you do not tighten the longer 25mm bolts into the mounting holes closest to the front of the bike as this will damage the captive dome nuts on the inside of the tail unit.
- Then pass the remaining 2x 20mm button head bolts (Item 4) through the forward mounting holes and hand tighten.
- Connect the indicator and number plate light connectors to the original sub loom.
Test the indicators and number plate light function correctly before continuing with the fitting.
- Then fully tighten the bolts to the required torque spec.
IMPORTANT: FOR SAFETY, ENSURE THE LICENCE PLATE IS PLACED AS HIGH AS
POSSIBLE ON THE TAIL TIDY (IT MAY REQUIRE DRILLING). IF FITTING A LICENCE
PLATE OF 200MM OR LONGER (INCLUDING ANY SHROUD OR REFLECTOR ATTACHMENT) TO THE
BRACKET, BEFORE RIDING, FULLY COMPRESS THE SUSPENSION TO ENSURE NO PART OF THE
ASSEMBLY CAN CONTACT THE TYRE WHILE THE VEHICLE IS IN MOTION OR UNDER LOAD. IT
IS YOUR RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE AVOIDING ACTION.
FAILURE TO CHECK THIS COULD RESULT IN SERIOUS INJURY OR DAMAGE TO THE
MOTORCYCLE.
ISSUE 1 30/05/2024 TB
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad
indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state
shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products
other than those in R&G’s order or confirmation and the Buyer confirms it has
chosen the Products as being of merchantable quality and suitable for its
particular purposes. Where R&G fits the Products or undertakes other services
it shall exercise reasonable skill and care and rectify any fault free of
charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of
the Products. On return of any defective Products R&G shall at its option
either supply a replacement or refund the purchase money but shall not be
liable if the Products have been modified or used or maintained otherwise than
in accordance with R&G’s or manufacturer’s instructions and good engineering
practice or if the defect arises from accident or neglect. Other than
identified above and subject to R&G not limiting its liability for causing
death and personal injury, it shall not be liable for indirect or
consequential loss and otherwise its liability shall be limited to the amounts
paid by the Buyer for the Products or the fitting or service concerned. These
terms do not affect the Buyer’s statutory rights.
R &G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be
rejected). Goods may only be returned direct to us if they were purchased
direct from us (customer must prove if necessary). Otherwise to be returned to
original vendor. Goods must be in re-sellable condition, in the opinion of R&G
Racing. All returns are subject to a 25% restocking and handling fee (25% of
the gross value exc. P&P – at the prevailing price at time of purchase). The
customer must pay any and all carriage charges. No returns of discontinued
products, unless within 14 days of purchase. This policy does not affect your
statutory rights and does not refer to faulty goods.
R &G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007
Fax: +44 (0)1420 87301 www.rg-racing.com
Email: info@rg-racing.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>