RAD0347PRO Moto Guzzi Stelvio Radiator Guard PRO Installation Guide

: September 21, 2024
: R G

Table of Contents

RAD0347PRO Moto Guzzi Stelvio Radiator Guard PRO
Specifications
FAQs
PRODUCT INFORMATION
TOOLS REQUIRED
GENERAL TORQUE SETTINGS
FITTING DIAGRAM
FITTING INSTRUCTIONS
MORE INFO
CONTACT INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RAD0347PRO Moto Guzzi Stelvio Radiator Guard PRO

Specifications

Product Name: RAD0347PRO
Description: Aluminium Radiator Guard
Components:
- 1 x RAD0347PRO (Aluminium Radiator Guard)
- 4 x RB0015 (Rubber Grommets)
- 4 x CT130 (One Way R&G Cable Ties)

FAQs

Q: Can rubber washers be discarded?
- A: Yes, if rubber washers are used to hold components onto bolts, they can be thrown away as per the instructions.
Q: Are digital copies of the instructions available?
- A: Yes, digital copies of the instructions can be downloaded from www.rg-racing.com.
Q: What is the return policy for discontinued products?
- A: No returns of discontinued products are accepted unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.

PRODUCT INFORMATION

THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER THE.
SOME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF MOUNTING TO THE BIKE.
IN THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS,
THESE RUBBER WASHERS CAN BE THROWN AWAY.

TOOLS REQUIRED

WIRE CUTTERS
10mm SOCKET & RACHET

GENERAL TORQUE SETTINGS

M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
M12 BOLT = 40Nm

LEGEND

ITEM NO.	DESCRIPTION	QTY
ITEM 1	RAD0347PRO (ALUMINIUM RADIATOR GUARD)	1
ITEM 2	RB0015 (RUBBER GROMMETS)	4
ITEM 3	CT130 (ONE WAY R&G CABLE TIES)	4

FITTING DIAGRAM

FITTING PICTURES

FITTING INSTRUCTIONS

Insert the 4x rubber grommets into the radiator guard in the holes circled in yellow (as shown above) if they do not come already installed.
Slide the R&G Radiator Guard into position. You will need to remove the bolt shown in Picture 1 to be able to slide the radiator guard behind the OEM plastic guard.
Secure in place using 4 x supplied R&G cable ties as shown in the Fitting Picture above, the cable ties should go through the 4 holes circled in green in the assembly diagram. The locking part of the cable tie needs to be secured from behind the radiator.

ISSUE 1 – 29/02/2024 (MH)

MORE INFO

CONSUMER NOTICE

The catalog description and any exhibition of samples are only broad indications of the Products and R&G may make design changes that do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes.
Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed.
The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than following R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect.
Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.

R &G RACING RETURNS POLICY (NON-FAULTY GOODS)

Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned directly to us if they were purchased directly from us (customer must prove if necessary).
Otherwise to be returned to the original vendor.
Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at the time of purchase).
The customer must pay all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.