R G PKS0176 Kickstand Foot Instructions

: June 15, 2024
: R G

Table of Contents

R G PKS0176 Kickstand Foot
Product Information
Product Usage Instructions
TOOLS REQUIRED
GENERAL TORQUE SETTINGS
LEGEND
EXPLODED ASSEMBLY DIAGRAM
FITTING INSTRUCTIONS
CONSUMER NOTICE
Contact Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

R G PKS0176 Kickstand Foot

Product Information

Specifications:

Mounting Plate (MP0281)
Clamp Plate (PLATE0310)
M5 x 10mm Long Stainless-Steel Countersunk Bolts
50mm Strip of Self-Adhesive Foam

Product Usage Instructions

Step 1: Checking Parts
Before proceeding with the fitting, make sure you have all the necessary parts mentioned in the exploded assembly diagram. Ensure everything is present to avoid any issues during installation.

Step 2: Required Tools
Make sure you have the following tools available:

Torque wrench
M4 Bolt = 8Nm
M5 Bolt = 12Nm
M6 Bolt = 15Nm
M8 Bolt = 20Nm
M10 Bolt = 40Nm
M12 Bolt = 40Nm

Step 3: Mounting the Kickstand Shoe

Place the mounting plate (MP0281) on the kickstand base.
Align the clamp plate (PLATE0310) with the mounting plate.
Insert the M5 x 10mm long stainless-steel countersunk bolts through the holes in both plates.
Tighten the bolts to their respective torque settings using a torque wrench.
If necessary, cut and place the strip of self-adhesive foam into the base plate to ensure a tight fit.

FAQ:

Q: What should I do if I’m unsure about fitting the product myself?
A: If you have any doubts or concerns about fitting our products, we recommend consulting one of our dealers or having the product fitted by a qualified technician.
Q: Can I throw away the rubber washers used to hold components onto bolts?
A: Yes, you can throw away the rubber washers if they are used in the installation process.

Note

This Kit contains the items pictured and labeled over the page.
Some parts may be shown for clarity of instructions only.
Do not proceed until you are sure all parts are present.
Please read all instructions before proceeding.

IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.

Please note that the way the kit is packed does not necessarily represent the way of mounting the bike.
In the event of rubber washers being used to hold components onto bolts, these rubber washers can be thrown away.

DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM

www.rg-racing.com

R &G

Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007
Fax: +44 (0)1420 87301
Web: www.rg-racing.com.
Email: info@rg-racing.com.

TOOLS REQUIRED

3mm A/F Allen key
Loctite blue 242

GENERAL TORQUE SETTINGS

M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
M12 BOLT = 40Nm

LEGEND

ITEM No.	DESCRIPTION	QTY
ITEM 1	MOUNTING PLATE (MP0281)	1
ITEM 2	CLAMP PLATE (PLATE0310)	1
ITEM 3	M5 x 10mm LONG STAINLESS-STEEL COUNTERSUNK BOLTS	4
ITEM 4	50mm STRIP OF SELF-ADHESIVE FOAM (NOT SHOWN)	1

EXPLODED ASSEMBLY DIAGRAM

FITTING INSTRUCTIONS

Carefully pass the clamping plate (Item 2) around the side stand leg with the countersinks facing upwards.
Take the machined aluminium mounting plate (Item 1) and fit to the base of the side stand from underneath.
Sandwich the two plates together around the side stand pad.
Apply a small amount (one drop) of the Loctite blue 242 to the threaded end of each countersunk bolt (Item 3).
Fit the four bolts (Item 3) through the clamp plate and into the mounting plate clamping the two plates securely together to the side stand pad.
Tighten all the bolts evenly and ensure the stand is clear of the swingarm and chain when in the raised position.
If fitting to older used stands that have wear the self-adhesive foam strip (Item 4) should be cut and placed into the base plate to ensure a tight fit.

See more R &G products for your Motorcycle in the links below:
R&G Racing | Frame sliders, crash protectors, and frame protectors from R&G for all sportsbikes. (rg-racing.com).

ISSUE 1 – 21/ 12/2022 (MH)

CONSUMER NOTICE

The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes that do not diminish their performance or visual appeal and supplying them in such a state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than per R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.

R &G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned directly to us if they were purchased directly from us (customer must prove if necessary). Otherwise to be returned to the original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at the time of purchase). The customer must pay all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.