R G ECC0355R BMW S Series Pulse Case Cover Protection Instruction Manual
- June 10, 2024
- R G
Table of Contents
R G ECC0355R BMW S Series Pulse Case Cover Protection
Product Information
ECC0355R RHS Engine Case Cover for BMW S1000RR 2009-2019 Pulse Cover
The ECC0355R RHS Engine Case Cover is a protective cover designed for use on BMW S1000RR motorcycles manufactured between 2009 to 2019. The cover is made by R&G and features a pulse cover design that adds an extra layer of protection to the engine case. The kit includes one engine case cover, two spacers, and a skidder that are pre-fitted onto the cover. The cover is made of high-quality materials that offer excellent resistance against impact and abrasion. The cover is also lightweight and easy to install, making it an ideal choice for riders who want to protect their engine case without compromising on performance or adding unnecessary weight to their motorcycle.
Product Usage Instructions
Before proceeding with the installation of the ECC0355R RHS Engine Case Cover, ensure that all components in the kit are present. Refer to page one of the user manual for a complete list of parts included in the kit.
- Begin by removing the existing low-profile spacers from the engine case.
- Next, remove the rubber washer, if present, from the M6 bolts on the engine case.
- Install the ECC0355R RHS Engine Case Cover onto the engine case using the M6 x 35mm long cap head bolts provided in the kit.
- Attach the engine case cover onto the motorcycle frame using the M6 x 30mm long special counter-sunk bolts (M0577) and low-profile spacers provided in the kit. Ensure that the spacers are in place before tightening the bolts.
- Tighten all bolts to the recommended torque settings provided in the user manual.
- After installation, inspect the installation of the engine case cover and ensure that there are no loose components or gaps between the cover and the engine case.
If you have any doubts or questions during the installation process, consult one of R&G’s dealers or have a qualified technician fit the product.
FITTING INSTRUCTIONS FOR ECC0355R RHS ENGINE CASE COVER
FOR BMW S1000RR 2009-2019 PULSE COVER
- THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE.
- SOME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY.
- DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
- PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING.
- IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
- PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF MOUNTING TO THE BIKE.
- IN THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS,
- THESE RUBBER WASHERS CAN BE THROWN AWAY.
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM
TOOLS REQUIRED
- Set of metric Allen keys to include 4 & 5mm A/F.
- 8mm Socket and wrench.
- Suitable Torque Wrench.
GENERAL TORQUE SETTINGS
- M4 BOLT = 8Nm
- M5 BOLT = 12Nm
- M6 BOLT = 15Nm
- M8 BOLT = 20Nm
- M10 BOLT = 40Nm
- M12 BOLT = 40Nm
LEGEND
FITTING INSTRUCTIONS
- Please ensure the engine is cold before proceeding with the fitment of the R&G engine case cover.
- Remove the four bolts arrowed in picture 2, hold the cover up to the casing to identify the correct bolts. DO NOT REMOVE ALL THE ENGINE CASE BOLTS.
- Offer the R&G cover up to the engine case (item 1) and carefully fit over the casing. Please ensure that the four bolt holes in the cover are aligned with the holes in the engine case and then push on as far as it will go.
- Fit the two cap head bolts (item 2) through the cover and into the top holes in the engine case cover (please see picture 2).
- Place the two low profile spacers (items 4) onto the special counter-sunk bolts (items 3) and then place the two bolts with spacers into the lower holes in the engine case cover (please see picture 2).
- Using a 4 & 5mm Allen key or socket bit tighten the bolts evenly to pull the cover into position. DO NOT FULLY TIGHTEN AT THIS STAGE.
- Finally use a torque wrench set at 10 N/m (7lb/ft) to fully tighten.
- It is suggested that you check the tightness of the mounting bolts after the first heat cycle and then on a regular basis i.e. – when cleaning or once a month.
- NOTE: – For the cleaning of this product you should only use a soft polishing cloth and a mild general cleaning agent.
- AVOID HARMFUL CHEMICALS. IF IN DOUBT DO NOT USE AS THEY COULD ALTER THE STRENGTH OF THE COVER.
- R&G will accept no liability if the above procedures and torque setting are not followed.
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.
R &G RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
R &G
- Unit 1, Shelley’s Lane, Eas t Worldham, Alton, Hamps hire, GU34 3AQ
- Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
References
- cing.com
- Welcome to R&G | Setting the standard in bolt-on motorcycle accessories and Crash Protectors
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>