GSX-8S Radiator Guard Instruction Manual
- June 15, 2024
- R G
Table of Contents
GSX-8S Radiator Guard
FITTING INSTRUCTIONS FOR RAD0317PRO
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE.
SOME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE
FITTED BY A QUALIFIED TECHNICIAN.
PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE
WAY OF MOUNTING TO THE BIKE.
IN THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS, THESE
RUBBER WASHERS CAN BE THROWN AWAY.
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM: WWW.RG- RACING.COM
TOOLS REQUIRED
- WIRE CUTTERS/SCISSORS
GENERAL TORQUE SETTINGS
M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
M12 BOLT = 40Nm
LEGEND
ITEM NO. | DESCRIPTION | QTY |
---|---|---|
TEM 1 | ALUMINIUM RADIATOR GUARD (RAD0317PRO) | 1 |
ITEM 2 | RUBBER BUNGS (RB0015) | 2 |
ITEM 3 | ONE WAY R&G CABLE TIES (CT130) | 3 |
ITEM 4 | CABLE TIE (CT220) | 4 |
FITTING DIAGRAM
FITTING PICTURE
Place the cable ties around the two brackets at the top of the radiator and through the holes in the bottom corners of the fins.
FITTING INSTRUCTIONS
- Insert the 4x rubber grommets into the radiator guard in the holes (as shown above) if they do not come already installed.
- Slide the R&G Radiator Guard into position (AS SHOWN IN THE PICTURE A ON PAGE 1).
- Secure in place using 4 x supplied R&G cable ties as shown in the Fitting Picture above, the cable ties should go through the 4X holes (AS SHOWN IN THE ASSEMBLY DIAGRAM).
- The locking part of the cable tie needs to be secured from behind the radiator; to do this it is likely you will have to remove the fairings to access the rear of the radiator. Please refer to the owner’s manual for information on how to do this.
ISSUE 1 – 30/08/2023 (JH)
ISSUE 2 – 06/09/2023 (JH)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad
indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state
shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title)
has been given or will apply to the Products other than those in R&G’s order
or confirmation and the Buyer confirms it has chosen the Products as being of
merchantable quality and suitable for its particular purposes. Where R&G fits
the Products or undertakes other services it shall exercise reasonable skill
and care and rectify any fault free of charge unless the workmanship has been
disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any
defective Products R&G shall at its option either supply a replacement or
refund the purchase money but shall not be liable if the Products have been
modified or used or maintained otherwise than in accordance with R&G’s or
manufacturer’s instructions and good engineering practice or if the defect
arises from accident or neglect. Other than identified above and subject to
R&G not limiting its liability for causing death and personal injury, it shall
not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the
fitting or service concerned. These terms do not affect the Buyer’s statutory
rights.
R &G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods۔
R &G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007
Fax: +44 (0)1420 87301
www.rg-racing.com
Email: info@rg-racing.com
References
- RACING.COM - YOUR RACING CONNECTION
- Welcome to R&G | Setting the standard in bolt-on motorcycle accessories and Crash Protectors
- Welcome to R&G | Setting the standard in bolt-on motorcycle accessories and Crash Protectors