MT-09 Givi Radiator Guard Instruction Manual
- June 15, 2024
- R G
Table of Contents
RAD0301PRO
FITTING INSTRUCTIONS FOR RAD0301PRO RADIATOR GUARD
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE.
SOME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR
HAVE FITTED BY A QUALIFIED TECHNICIAN.
PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF MOUNTING TO THE BIKE.
IN THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS, THESE RUBBER WASHERS CAN BE THROWN AWAY.
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
TOOLS REQUIRED | GENERAL TORQUE SETTINGS |
---|
• Socket and ratchet set to include 8mm and 10mm A/F or spanners.
• Wire cutters or scissors.| M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
M12 BOLT = 40Nm
LEGEND
ITEM NO. | DESCRIPTION | QTY |
---|---|---|
ITEM 1 | RADIATOR GUARD (RAD0301) | 1 |
ITEM 2 | RUBBER BUNGS (RB0015) | 4 |
ITEM 3 | CT220 (2.5mm CABLE TIES) | 4 |
FITTING PICTURE
FRONT OF BIKE
FITTING INSTRUCTIONS
- Remove the two top radiator mounts.
- Insert the 4x rubber grommets into the radiator guard in the holes circled in yellow (as shown above) if they do not come already installed.
- Offer up the R&G radiator guard and make sure that the radiator guard is in the correct position, before tightening the OEM bolts to their required torque setting.
- Attach one of the supplied cable ties to the bottom tab radiator to ensure a secure fit.
- Once the cable tie is secure, trim off the excess with a pair of scissors.
See more R &G products for your Motorcycle in the links below:
R&G Racing | Cleaning/Lubrication – Gleam range for All Vehicles (rg-
racing.com)
ISSUE 1 - 20/03/2023 (MH)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.
R &G RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
R&G
Unit 1, Shelley’s Lane, East Worldham , Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fa x: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
References
- cing.com
- Welcome to R&G | Setting the standard in bolt-on motorcycle accessories and Crash Protectors
- Welcome to R&G | Setting the standard in bolt-on motorcycle accessories and Crash Protectors
- Welcome to R&G | Setting the standard in bolt-on motorcycle accessories and Crash Protectors
- R&G Racing | Cleaning/Lubrication - Gleam range for All Vehicles