R AND G RAD0324PRO Racing Pro Radiator Guard Instructions

: June 8, 2024
: R AND G

Table of Contents

R AND G RAD0324PRO Racing Pro Radiator
Specifications
Product Usage Instructions
TOOLS REQUIRED
GENERAL TORQUE SETTINGS
FITTING DIAGRAM
FITTING INSTRUCTIONS
CONSUMER NOTICE
FAQ
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

R AND G RAD0324PRO Racing Pro Radiator

Specifications

Model: RAD0324PRO
Manufacturer: R&G Racing
Contents: Radiator guard, rubber bung, cable tie

Product Usage Instructions

Tools Required
Make sure you have the following tools before starting the installation:

M4 Bolt: 8Nm
M5 Bolt: 12Nm
M6 Bolt: 15Nm
M8 Bolt: 20Nm
M10 Bolt: 40Nm
M12 Bolt: 40Nm

Fitting Instructions

Ensure all parts are present as shown in the fitting diagram.
Refer to the fitting pictures for visual guidance.
Follow the steps outlined in the manual carefully.
If in doubt, consult a dealer or a qualified technician.

Additional Notes

Do not discard rubber washers used to hold components onto bolts.
The way the kit is packed may not necessarily represent the mounting method of the bike.

THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE.

SOME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT

PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.

PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF MOUNTING TO THE BIKE.
IN THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS, THESE RUBBER WASHERS CAN BE THROWN AWAY.

DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM

TOOLS REQUIRED

SET OF ALLEN KEYS
WIRE CUTTERS

GENERAL TORQUE SETTINGS

M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
M12 BOLT = 40Nm

LEGEND

ITEM NO.	DESCRIPTION	QTY
ITEM 1	RAD0337 RADIATOR GUARD	1
ITEM 2	RUBBER BUNG	4
ITEM 3	CABLE TIE	4

FITTING DIAGRAM

FITTING PICTURES

FITTING INSTRUCTIONS

To fit the R&G radiator guard to the bike, insert the 7x rubber grommets into the radiator guard in the holes circled in yellow in the Fitting Diagram if they do not come already installed & slide the R&G Radiator Guard into position.
Offer the R&G Radiator Guard into position and secure the radiator guard in place using 8x supplied R&G one-way cable ties through the holes circled in green in the Assembly Diagram, the locking part of the cable tie needs to be secured from behind the radiator as shown in Picture 1.
It may be necessary to remove the bodywork surrounding the radiator to get the guard into place – please refer to the owner’s manual to do this.
Cut the excess material from the cable tie.

CONSUMER NOTICE

The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than by R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.

R &G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned directly to us if they were purchased directly from us (customer must prove if necessary). Otherwise to be returned to the original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at the time of purchase). The customer must pay any carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods

R &G Racing

Address: Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007
Fax: +44 (0)1420 87301
www.rg-racing.com
Email: info@rg-racing.com

FAQ

Q: Can I download digital copies of the instructions?
- A: Yes, you can download digital copies of the instructions from www.rg-racing.com.
Q: What should I do if I am missing a part?
- A: Do not proceed with the installation if you are missing any parts. Contact our customer service for assistance.
Q: Can I use different torque settings than specified?
- A: It is recommended to use the torque settings provided to ensure proper installation and safety