R G Racing PKS0176 Kickstand Foot Instruction Manual

R G Racing PKS0176 Kickstand Foot

This Kit contains the items pictured and labelled over page. Some parts may be shown for clarity of instructions only. Do not proceed until you are sure all parts are present. Please read all instructions before proceeding.

IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.

• Please note that the way the kit is packed does not necessarily represent the way of mounting to the bike.
• In the event of rubber washers being used to hold components onto bolts, these rubber washers can be thrown away.

TOOLS REQUIRED

• 3mm A/F Allen key
• Loctite blue 242

GENERAL TORQUE SETTINGS

• M4 BOLT = 8Nm
• M5 BOLT = 12Nm
• M6 BOLT = 15Nm
• M8 BOLT = 20Nm
• M10 BOLT = 40Nm
• M12 BOLT = 40Nm

LEGEND

EXPLODED ASSEMBLY DIAGRAM

FITTING INSTRUCTIONS

• Carefully pass the clamping plate (Item 2) around the side stand leg with the countersinks facing upwards.
• Take the machined aluminium mounting plate (Item 1) and fit to the base of the side stand from underneath.
• Sandwich the two plates together around the side stand pad.
• Apply a small amount of (one drop) of the Loctite blue 242 to the threaded end of each countersunk bolts (Item 3).
• Fit the four bolts (Item 3) through the clamp plate and into the mounting plate clamping the two plates securely together to the side stand pad.
• Tighten all the bolts evenly and ensure the stand is clear of the swingarm and chain when in the raised position.
• If fitting to older used stands that have wear the self-adhesive foam strip (Item 4) should be cut and placed into the base plate to ensure a tight fit.
• See more R&G products for your Motorcycle in the links below:
• R&G Racing | Frame sliders, crash protectors, frame protectors from R&G for all sportsbikes. ( rg-racing.com )

CONSUMER NOTICE

The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.

R &G RACING RETURNS POLICY (NON-FAULTY GOODS)

Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.

R &G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007
Fax: +44 (0)1420 87301
www.rg-racing.com
Email: info@rg-racing.com

References

• RACING.COM - YOUR RACING CONNECTION
• Welcome to R&G | Setting the standard in bolt-on motorcycle accessories and Crash Protectors

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>