DJI DF03-004 Focus Pro Hand Unit User Guide

DJI DF03-004 Focus Pro Hand Unit

Product Specifications

• Model: DF03-004
• Operating Frequency: 2400-2483.5MHz
• Mode: BLE8dBm (EIRP) (CE) GFSK16dBm (EIRP)(CE)

Product Usage Instructions

1. Trigger: Press once to lock or unlock the subject in Auto mode.
2. Screw Hole
3. Video Transmission Port
4. Focus Wheel: Turn to focus.
5. Focus Mark Ring
6. Zoom Button: Push to zoom in/out.
7. Touchscreen
8. M Button: Press once to switch auto/manual focus.
9. A/B Point Setting Button: Press once to record/delete limited point.
10. REC Button: Press once to start/stop recording. Press and hold to power on/off.
11. Aperture Slider: Slide to control aperture.
12. Aperture Marker
13. Battery Compartment: Insert batteries into the  battery compartment for power supply.

Frequently Asked Questions (FAQ)
How do I link the hand unit to the focus motor?
To link the hand unit to the focus motor, slide down on the touchscreen and tap for linking.

DJI Focus Pro Hand Unit User Guide

Instructions

1. Trigger
   Press once to lock or unlock the subject in Auto mode.

2. Screw Hole

3.  Video Transmission Port

4. Focus Wheel
   Turn to focus.

5. Focus Mark Ring

6. Zoom Button
   Push to zoom in/out.

7. Touchscreen

8. M Button
   Press once to switch auto/manual focus.

9. A/B Point Setting Button
   Press once to record/delete limited point.

10. REC Button
    Press once to start/stop recording. Press and hold to power on/off.

11. Aperture Slider
    Slide to control aperture.

12. Aperture Marker

13. Battery Compartment

Power Supply

Insert batteries into the battery compartment for power supply.

Linking
Slide down on the touchscreen and tap for linking to the focus motor

Specifications

GFSK＜16dBm (EIRP) (CE)

FCC Compliance Notice

• Supplier’s Declaration of Conformity
• Product name: DJI Focus Pro Hand Unit
• Model Number: DF03-004
• Responsible Party: DJI Research LLC
• Responsible Party Address: 17301 Edwards Road, Cerritos, CA 90703

Website: www.dji.com

We, DJI Research LLC, being the responsible party, declares that the above- mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions to satisfy RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA).
These requirements set a SAR limit of 4 W/kg averaged over ten gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the limbs.

ISED Compliance Notice

CAN ICES-003 (B) / NMB-003(B)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

EU & UK Compliance Notice

EU Compliance Statement: SZ DJI Osmo Technology Co., Ltd. hereby declares that this device (DJI Focus Pro Hand Unit) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU.

A copy of the EU Declaration of Conformity is available online at www.dji.com /euro-compliance
EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

Compliance Statement: SZ DJI Osmo Technology Co., Ltd. hereby declares that this device (DJI Focus Pro Hand Unit) is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017.
A copy of the GB Declaration of Conformity is available online at www.dji.com /euro-compliance

References

• DJI - Official Website

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>