BANNER R95-8M125 Series I/O Junction Block Owner’s Manual
- September 16, 2024
- BANNER
Table of Contents
BANNER R95-8M125 Series I/O Junction Block
Specifications
- Voltage Input Range: 30 V DC
- Maximum Current: 8A total, 2A max. per connector
Product Overview
Banner’s Molded Junction Blocks are designed to help customers reduce
wiring and to simplify connecting multiple products.
Mechanical Installation
Install the R95 I/O Junction Block to allow access for functional checks,
maintenance, and service or replacement. All mounting hardware is supplied by
the user. Fasteners must be of sufficient strength to guard against breakage.
Use of permanent fasteners or locking hardware is recommended to prevent the
loosening or displacement of the device. The mounting hole (4.5 mm) in the R95
I/O Junction Block accepts M4 (#8) hardware. See the figure below to help in
determining the minimum screw length.
CAUTION: Do not overtighten the R95 I/O Junction Block’s mounting screw
during installation. Overtightening can affect the performance of the R95 I/O
Junction Block.
Product Usage Instructions
Wiring
LED Models:
Refer to the wiring diagram for LED models provided in the manual and
ensure proper connection according to the color codes.
Flying Lead Model:
Follow the wiring instructions for the flying lead model as outlined in the
manual. Connect the appropriate wires to their corresponding ports.
M23 Model:|
For M23 models, refer to the wiring diagram provided in the manual and
connect the wires accordingly based on the pin configuration.
Accessories
Cordsets are available for additional connectivity options. Refer to the
accessories section of the manual for more information on compatible cordset
models.
FAQ
-
Q: Can I use this Junction Block with voltages other than 30 V DC?
A: No, the specified voltage input range for this product is 30 V DC. Using higher voltages may damage the device. -
Q: What is the maximum current rating per connector?
A: The maximum current per connector is 2A, with a total maximum current of 8A across all connectors.
R95 I/O Junction Block Product Manual
Features
8-Port Junction Block with 16 Signals
- Capable of handling 16 individual PNP signals into a singular point of entry Supports 8A combined between all devices connected
- Pin 2 and Pin 4 on the M12 for each individual signal
- Home run cabling options include a flying lead exit in varying lengths or a short 0.3 m M23 male 19-pin quick-disconnect connector
- Fully overmolded with a rugged TPU body
- Immediate field feedback with LEDs for signal and power status
- Wiring diagram included on body for quick problem diagnosis
Models
LED Models
| Model | Ports | Home Run Connector | Wiring |
|---|---|---|---|
| R95-8M125-C1-D24P | __ |
__
(8) Integral 5-pin M12 female quick-disconnect connectors
| 1 m (3.28 ft) black PVC cable with flying leads| __
__
See “Wiring” on page 2
__
R95-8M125-0.3M23-D24P
| 0.3 m (0.98 ft) black PVC cable with a 19-pin M23 male quick- disconnect connector
Non-LED Models
| Model | Ports | Home Run Connector | Wiring |
|---|---|---|---|
| R95-8M125-C1-D24 | __ |
__
(8) Integral 5-pin M12 female quick-disconnect connectors
| 1 m (3.28 ft) black PVC cable with flying leads| __
__
See “Wiring” on page 2
__
R95-8M125-0.3M23-D24
| 0.3 m (0.98 ft) black PVC cable with a 19-pin M23 male quick- disconnect connector
Product Overview
Banner’s Molded Junction Blocks are designed to help customers reduce wiring and to simplify connecting multiple products.
The 8-Port I/O Junction Block:
- Allows up to 16 individual PNP devices connected
- Provides 8A of power shared between all devices connected on the 18 Awg power conductors from a panel or control source Includes a singular connection back to the control device or panel to manage all of these devices on 22 awg wire
- Has non-LED options to allow for any signal type to be combined into the block
Mechanical Installation
Install the R95 I/O Junction Block to allow access for functional checks, maintenance, and service or replacement.
All mounting hardware is supplied by the user. Fasteners must be of sufficient strength to guard against breakage. Use of permanent fasteners or locking hardware is recommended to prevent the loosening or displacement of the device. The mounting hole (4.5 mm) in the R95 I/O Junction Block accepts M4 (#8) hardware. See the figure below to help in determining the minimum screw length.
NOTE: The dotted line indicates the profile of the counterbore.
CAUTION : Do not overtighten the R95 I/O Junction Block’s mounting screw
during installation. Overtightening can affect the performance of the R95 I/O
Junction Block.
Wiring
LED Models 
Non-LED Models 
Specifications
- Voltage Input Range
- 30 V DC
- Maximum Current
- 8A total
- 2A max. per connector
Construction
- Coupling Material: Nickel-plated brass
- Connector Body: TPU black
Operating Conditions
- 40 °C to +70 °C (–40 °F to +158 °F)
- 90% at +70 °C maximum relative humidity (non-condensing)
- Storage Temperature: –40 °C to +80 °C (–40 °F to +176 °F)
Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise. The measurements provided are subject to change.
Accessories
Cordsets
Other Accessories
ACC-CAP M12-10
- 10 Caps
- Seal and protect exposed, unterminated cascade quick-disconnect connectors
Maintenance and Service
Do not use alcohol-based cleaning agents. The R95 I/O Junction Block is
maintenance-free.
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in
material and workmanship for one year following the date of shipment. Banner
Engineering Corp. will repair or replace, free of charge, any product of its
manufacture which, at the time it is returned to the factory, is found to have
been defective during the warranty period. This warranty does not cover damage
or liability for misuse, abuse, or the improper application or installation of
the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER
EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING
UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties.
All specifications published in this document are subject to change; Banner
reserves the right to modify product specifications or update documentation at
any time. Specifications and product information in English supersede that
which is provided in any other language. For the most recent version of any
documentation, refer to:
www.bannerengineering.com.
For patent information, see www.bannerengineering.com/patents.
© Banner Engineering Corp. All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>