ELECTOP KS-WLR08 Remote Control Outlet User Manual
- June 17, 2024
- ELECTOP
Table of Contents
- Remote control
- Pairing
- Countdown setting and canceling function
- Adding or removing remote controls from the paired remote control panel
- Delete the paired plug
- DIY pairing
- Installation warnings
- Installation warnings
- Installment and dismantle
- Wiring method of receiver
- Specifications
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ELECTOP KS-WLR08 Remote Control Outlet
Note: The product pictures are for reference only, Subject to the purchased product.*
Remote control
Countdown remote control can be paired with the following products:
Note: Pairing and code deletion operations are the same for all products. This manual uses the wireless plug as an example
Pairing
(The remote control,wireless plug , light socket, and receiver must be paired before use.)
- Press the set button in the plug for 2s
- The light flashes, then release your finger
- Press the corresponding ON/OFF button on the remote control for the desired number
- When the LED indicator on the side of the plug is on, the pairing is successful.
Countdown setting and canceling function
- Use the button to select from 5 different countdown options: 0.5, 1, 2, 4, 8 hours.
- Illuminate the desired countdown number and release the button.
- Press the corresponding button on the paired remote control. The wireless plug indicator light will flash red, indicating that the countdown has started.
- To cancel the countdown, press the button or the button corresponding to the countdown number already set.
Adding or removing remote controls from the paired remote control panel
-
To add multiple remote controls
-
Press and hold the corresponding button on the paired remote control (about 16s).
-
The LED indicator will flash quickly. Release the button.
-
Press the corresponding 【 ON/OFF 】button on the new remote control. The function assigned to the corresponding number on the original remote control will be copied.
-
To delete a paired remote control ( Operate with caution! )
-
Press and hold the corresponding 【 ON/OFF 】 button on the paired remote control (about 40s).
-
The status of the LED indicator changes as follows: (Fast flash → off )→ (slow flash for 8 times → off) →slow flash (then loosen your grip), and then press the panel key again to complete the code deletion operation.
Delete the paired plug
(Operate with caution!)
Press the setting button in the plug for about 10s, the LED indicator will be fast flashing becomes slow flashing, just release your finger when flashing slowly.
DIY pairing
One remote control can control 3 plugs , each of which can control multiple plug within its range.
Press button: Set countdown
Remote control disassembly and battery replacement
Disassembly:
Insert your hand into the bottom slot and open the bottom. Then, starting from the side, press the clips one by one to open the casing.After prying it open, gently pry the casing with your hand.
Battery replacement:
Use a straight screwdriver to push the battery down and remove it. Replace the battery (pay attention to the positive and negative directions).
CAUTION:
- Please replace the battery strictly in accordance with the model requirements in user manual to avoid the risk of explosion;
- Please put the replaced battery in a safe area and away from children’s reach to avoid burns and death risks caused by accidental ingestion.
Installation warnings
- Plug into a three-hole plug with a ground wire.
- Do not install wireless plugs in areas with high pollution or high humidity.
- Try not to install the wireless plug in direct sunlight or where the long-term working temperature exceeds the limit, which will shorten the service life of the product.
- Before installation, it should be tested repeatedly to be able to switch normally and control the plug work. If it does not work properly, change the installation position or check the surroundings whether there is strong electromagnetic interference.
- After connecting the wireless plug, turn on the power and press the button on the side of the plug,the LED indicator can be on or off, indicating that the plug is normal.
- There is contact detection inside the wireless plug. When the plug can’t be inserted in stably, it will automatically disconnect the output voltage, which greatly improves the safety of electricity.
No Power Troubleshooting:
-
Plug inserted into socket on one side only
-
Spacing between plug and socket greater than 5 mm
-
Insertion process is slow
-
Plug pin width less than 4.35mm
Installation warnings
- The remote control light socket is for indoor use, please do not install it in the place exposed to direct sunlight, rain, long-term working temperature exceeds the limit value or high pollution and high humidity, which will shorten the service life of the remote control light socket controller.
**Installation diagram:
Rotate into the socket base**
Note: After installing the light socket, please pair the Countdown remote control and the light socket before use. For instructions please refer to page 1 entitled “Pairing”.
Installment and dismantle
- Loosen the screws with a screwdriver
- Each wire end is 8mm exposed and then inserted into the corresponding wiring hole;
- Then tighten the screws with a screwdriver and cover with silicone
Wiring method of receiver
Note: After installing the receiver, please pair the Countdown remote control and the receiver before use. For instructions please refer to page 1 entitled “Pairing”.
“Open”/”Close” state settings of the receiver used together with traditional switch
Note: The receiver is default in close state when leaving the factory.
- Power off electricity, install the receiver as the diagram, and distinguish live from neutral lines.
- Power on electricity, then program receiver with the switch according to the Learning code operation chapter.
Wiring diagram of adding remote control to traditional switch
Countdown remote control
What is the difference between the “Open” and “Close” states when used with a traditional switch?
If the receiver is in the “Open” state, turn on the traditional switch, and the light will be on immediately;
If the receiver is “Close”, turn on the traditional switch, you also need to press the remote control to turn on the light.
Whether the receiver is in an Open or Close state, only if turn on the traditional switch could you control lights using the remote control.
Setting Open / Close state of receiver
Press and hold setting button for 16s, loosen your finger when the indicator
light is continuously bright. (During the 16s, the indicator light will change
from quick flash to slower flash, after that, the indicator light will be off,
then will be on.)
Specifications
Specifications of Receiver
Model: SW-R01 | Model: SW-R03 |
---|---|
Standby power consumption: ≤0.05W | Standby power consumption: ≤1.1W |
Working power consumption: ≤0.8W | Working power consumption: ≤1.3W |
Working frequency: 433 Mhz | Working frequency: WiFi 2.4G&433 Mhz |
Dimension : 52 x 26 x 23(mm)
Current : 10A
Working voltage : AC 80~275V
Relay life : 400K times on/off
LED Lamp /CFL Lamp : ≤1000W
Fluorescent lamp: ≤ 1200W
Incandescent lamp : ≤1800W
Fireproof level : V0
Working temperature : -40 ~ +70℃
Storage temperature : -40 ~ +80℃
Specifications of Light socket
Model: SW-R04 | Model: SW-R04 |
---|---|
Standby power consumption: ≤0.05W | Standby power consumption : |
≤0.75W
Working power consumption : ≤0.6W| Working power consumption : ≤1.0W
Working frequency: 433 Mhz| Working frequency: WiFi 2.4G&433 Mhz
Dimension : 85 x 43 x 43(mm)
Current : 5A
Working voltage : AC 80~275V
Relay life : 400K times on/off
Key lifespan : 50K times
Incandescent lamp : ≤800W
LED/CFL lamp : ≤500W
Fireproof level : V0
Working temperature : -40 ~ +70℃
Storage temperature : -40 ~ +80℃
Specifications of Wireless plug
Model: SW-R05 | Model: SW-R05 |
---|---|
Standby power consumption: ≤0.05W | Standby power consumption: ≤0.9W |
Working power consumption: ≤0.8W | Working power consumption: ≤1.0W |
Working frequency: 433 Mhz | Working frequency: WiFi 2.4G&433 Mhz |
Dimension : 52 x 52 x 25(mm)
Current : 15A
Working voltage : AC 80~275V
LED/CFL lamp : ≤1500W
Relay life : 400K times on/off
Key lifespan : 50K times
Fireproof level : V0
Working humidity : 0 ~ 90%
Working temperature : -40 ~ +70℃
Storage temperature : -40 ~ +80℃
Specifications of Countdown remote control
Model | SW-NK3G |
---|---|
Dimension | 135 x 40 x 1(4 mm |
Switch panel lifespan | 400K times |
Wireless range | 30~150 m |
Battery model | CR2032 |
Life of the battery | 6 ~ 10 years |
Standby current | ≤ 0.01 uA |
Working frequency | 433.92 MHz |
Fireproof level | V0 |
Working temperature | -40 ~ +70℃ |
Working humidity | 0 ~ 90% |
Storage temperature | -40 ~ +80℃ |
Most of the data in this manual comes from the company’s laboratory tests.