HORMANN H3-1 G OD Fire Protection Door User Guide

: September 18, 2024
: HORMANN

Table of Contents

H3-1 G OD Fire Protection Door
About These Instructions
General information
Notes on fire protection, smoke protection
Notes on multi-purpose doors
Notes on the illustrated section
ID plate
Declaration of performance
Fitting confirmation
Read User Manual Online (PDF format)
Download This Manual (PDF format)

M1.1 ➞ M1.3
M2.1 ➞ M2.6
M3.3
User Guide

H3-1 G OD Fire Protection Door

Instructions for fitting
Outside application for fire-rated, smoke-tight and multi-purpose doors OD doors, H3-1 G, H3-2 VM, HS 75, H16-1 S
Dissemination as well as duplication of this document and the use and communication of its content are prohibited unless explicitly permitted. Noncompliance will result in damage compensation obligations. All rights reserved in the event of patent, utility
model or design model registration. Subject to changes.
Dear Customer,
We are delighted that you have chosen a product from our company.

About These Instructions

Observe the instructions concerning this document for planning, fitting, operating and maintenance M1.1 to M1.3 and M2.1 to M2.5. These instructions contain important information on fitting, maintenance and care of your door.
The instructions are important documents for the construction file.
For additional information, contact customer service.
1.1 Symbols used

| Important note for avoiding damage to property
---|---
| Permissible arrangement or activity
| Gas concrete
| Fire protection
| Insulation material A (EN 13501-1)
| Non-permissible arrangement or activity
| Brickwork, concrete
| Mortar
| Smoke protection

General information

Before fitting, check whether the door is suitable for fitting.
Make sure that the wall is suitable for fitting the external door.
Follow the applicable building regulations.
Protect the structural gap on the weather side against penetrating moisture in a proper manner.

Based on construction measures, such as protected fitting positions, walkway, canopy and / or side fascia, the requirements profile for the door may change.

Notes on fire protection, smoke protection

Use of a hold-open device is not permitted.
When fitting an overhead door closer, please note the information from the manufacturer. We recommend fitting on the inside.
In conjunction with a retractable bottom seal, use a protruding threshold, see illustrated section, item 4.3.
Observe Table 2 of the instructions for planning, fitting, operating and maintenance M2.1 to M2.5.
When fitting to concrete walls, brickwork and gas concrete.
Do not use a hinged door operator.
Adverse weather effects such as solar radiation can cause temporary deformation of the door leaf.
Dark paints increase this effect, which is no cause for complaint. We recommend light, reflective paints.
Avoid using doors with glazing, ventilation grilles and top part in areas subject directly to adverse effects of the weather.

Notes on multi-purpose doors

For doors without acoustic insulation and burglar protection, you do not necessarily have to backfill the frames. We do recommend backfilling them, however.
Hold-open devices are possible. Observe the information from the system manufacturer.

Notes on the illustrated section

See figures	Measures required on the weather side
2, 3	* Flexible sealing

Sealing e.g. metal angles or plastic strips provided on-site
* Glazing tape, Kerafix 2000 for fire and smoke protection
*** Sealing cord
4| Sealing only in case of direct weathering

ID plate

www.hoermann.com/dop

6.1 Product Standards
6.2 Identification block

DOP 0030	Declaration of performance
99999999999999	number

DoP = Declaration of
Performance
Product with declaration of
performance and CE marking
0030| Code of the manufacturing factory
99999999999999| Article number (series
production) Commission and
item no. (customised
production)
H3-1 OD| Trade name of the door type
99999999| Unique serial number

6.3 Fire protection classification

E = partition in case of fire
EI1 and EI2= Partition and thermal insulation
EW = Partition and radiation protection
Sa = smoke tightness at ambient temperature
S200= smoke tightness at a mid-range temperature
C = Self-locking; C5 = usage category ≥ 200000 closing cycles

Declaration of performance

For the declaration of performance, go to: www.hoermann.com/dop

Fitting confirmation

Deliver this confirmation as well as the fitting and maintenance instructions to the building owner before initial start-up of the product. The building owner must keep these documents on file and provide them to the responsible building supervisory authorities if necessary.
Construction project……………………………………………………..
Street………………………
Postal code, city……………………………..
Position in the building (e.g. building part, floor, door………………………….
number)……………………….
Fitting date and fitting period………………………

Identification of the fire protection, smoke-tight door assembly
Manufacturer…………………………………………………
Product type, product designation………………………….
Serial number or reference number of the product……………………………..
Fire resistance classification, smoke protection classification and classification of self-closing………………………….

Information on the company and specialist personnel
Name ………………………………………………….
Postal code, city…………………………………..
Name of specialist personnel………………………………….

Confirmation of specialist personnel
Confirmation of the professional fitting of the above fire protection, smoke- tight door assembly in accordance with the fitting instructions:
Name ……………………………………….
Postal code, place, date…………………………….
Signature……………………..

Fischer: FUR 10 × 80/100
Fischer: DuoXpand 10 × 80/100
CELO: HBR 10 × 80/100
Fischer: SXRL 10 × 80/100
Hilti: HRD 10 × 80/100
CELO: MFR 10 × 80/100
Würth: W-UR 10 × 80/100
Fischer: FUR 10 × 80/100/115
Fischer: DuoXpand 10 × 80/100/120
Fischer: SXRL 10 × 80/100/115
Hilti: HRD 10 × 80/100
CELO: MFR 10 × 80/100/115
CELO: HBR 10 × 80/100/115
Würth: W-UR 10 × 80/100/115
Fischer: FUR 10 × 100
Fischer: DuoXpand 10 × 100
CELO: HBR 10 × 100
Fischer: FUR 10 × 160
Fischer: DuoXpand 10 × 160
CELO: HBR 10 × 160
Fischer: FUR 10 × 200
Fischer: DuoXpand 10 × 200
CELO: HBR 10 × 200
8 × 40

| Managementsysteme
DIN EN ISO 9001 — Qualitat
DIN EN ISO 14001 — Umwelt
DIN EN ISO 50001 — Energie
BS OHSAS 18001 — Arbeitsschutz
Reg.=Nr.: 7050542
---|---
| Produktqualitat
VOC Emissionen aus Bauprodukten
QM 359
Reg.-Nr.: 247 7050542

Hörmann KG Verkaufsgesellschaft
Upheider Weg 94-98
33803 Steinhagen, Deutschland