SUNLITE 88090-SU LED T8 Plug and Play 12w Light Bulb 3000K Warm Instruction Manual
- June 4, 2024
- sunlite
Table of Contents
- SUNLITE 88090-SU LED T8 Plug and Play 12w Light Bulb 3000K Warm
- Product Features
- Product Applications
- Installation Instructions
- Turn Power OFF
- Switch power ON
- Instant Start Ballast Wiring Diagram Correct
- Instant Start Ballast Wiring Diagram Wrong
- Safety Information
- Maintenance
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SUNLITE 88090-SU LED T8 Plug and Play 12w Light Bulb 3000K Warm
Product Features
UL certified Plug-n-Play replacement Full glass housing: No Aging, Yellowing. Bending. Compatible with Instant Start, Program Start and Rapid Start T8 electronic Ballast; Compatible with T8 emergency Ballast and dimmable Ballasts.
Product Applications
Widely used in residential buildings, offices, shopping malls, supermarkets, hospitals, assembly lines, warehouses, etc. for energy saving illumination.
Installation Instructions
Please completely comply with these instructions and notes, to ensure that the product is operated in a safe condition.
Safety Precautions
WARNING
Risk of shock
Disconnect power before installation. LED T8 lamp for use only with products described and installed in accordance with product specifications. LED T8 lamp to be operated with fluorescent electronic ballast.
RISK OF FIRE
USE ONLY IN PLACE OF FLUORESCENT LAMPS SPECIFIED ON LABEL.
RISK OF ELECTRIC SHOCK
SUITABLE FOR DAMP LOCATIONS.
Turn Power OFF
- Remove lens or diffuser if applicable.
- Remove existing fluorescent lamps from the luminaire.
Bring LED lamp to luminaire and
insert lamp pins into luminaire lamp holders.
Rotate LED lamp until lamp locks in place. Ensure that the LED lamp front points away from the back of the luminaire. Note: install LED T8 replacement lamp one for each fluorescent lamp removed. Place lens or diffuser back in place if applicable
Switch power ON
Instant Start Ballast Wiring Diagram Correct
Two Lamp Ballast Correct Wiring
Three Lamp Ballast Correct Wiring
Four Lamp Ballast Correct Wiring
Instant Start Ballast Wiring Diagram Wrong
Two Lamp Ballast Wrong Wiring
Three Lamp Ballast Wrong Wiring
- DO NOT INSTALL THIS LAMP IN APRE HEAT LUMINAIRE.
- THIS LAMP ONLY OPERATES ON ELECTRONIC BALLASTS.
- IF LAMP DOES NOT LIGHT WHEN THE LUMINAIRE IS ENERGIZED, REMOVE LAMP FROM LUMINAIRE AND CONTACT LAMP MANUFACTURER OR QUALIFIED ELECTRICIAN.
CAUTION
RISK OF FIRE
- IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE OPERATION BUZZING, FLICKERING, ETC.
- IMMEDIATELY TURN OFF POWER, REMOVE LAMP FROM LUMINAIRE AND CONTACT MANUFACTURER.
Safety Information
- Check the lamp before installation, if there is any damage caused during transportation, do not install.
- Maintenance should be carried out by technical personnel only.
- Do not stare at the light source with bare eyes for a long time, or beam to others’ eyes.
- Do not place any objects on the lamp.
- Keep the lamp away from flame or high temperature objects.
- Only replace with same type of LED tube.
Risk of electrical shock
If the glass lamp tube is broken, the lamp must be disposed of immediately.
Maintenance
Notes
- Disconnect lamp from power supply before any maintenance.
- Clean luminaire with dry cloth.
- Do not clean the lamp with corrosive chemicals.
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Sunshine Lighting Company 744 CLINTON BROOKLYN,NY 11231 USA TEL:718-768-7000 FAX:718-768-0970
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>