GOLDEN LIGHTING 3690-6 Kennedy 6 Light Chandelier Instruction Manual
- June 17, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 3690-6 Kennedy 6 Light Chandelier Instruction Manual
Thank You for Choosing Golden Lighting for Your Lighting Needs!
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor.
Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure
the best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit : www.GoldenLighting.com.
Assembly Instructions
How to Identify the Fixture’s Wires
- Fixture Wires
- Hot
- Neutral
- Ground
- House Wires
- Hot
- Neutral
- Ground
Hot: Smooth, Black, or Transparent with Black Inner Thread
For Customer Service, contact the place of purchase to arrange for
replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. From the parts bag remove the mounting strap assembly.
Mounting strap (B) contains several threaded holes. Two sets of mounting
screws (A & D) should be attached to mounting strap (B). You may need to
tighten nuts (C) that hold mounting screws (A) in place. If the screws are not
attached, please hold canopy (F) up to mounting strap (B). Line up the holes
in canopy (F) with the holes in mounting strap (B) and insert mounting screws
(A) into mounting strap (B) so that mounting screws (A) protrude through the
holes in canopy (F). Mounting screws (A) are long, so please test the canopy
against the mounting strap to see how far you should insert the screws. Remove
the canopy and then tighten nuts (C) onto mounting screws (A) to hold the
screws in place. 2. Pull the house wire though the center of the mounting
strap (B).
Place mounting strap (B) over the junction box and secure in place with
mounting screws (D). Tighten the screws securely with a screwdriver.
ASSEMBLING THE FIXTURE
3. Measure to determine the correct number of rods (H) needed for proper
hanging height. To shorten the fixture, slide the desired number of excess
rods off. To lengthen the fixture, add additional rods. If additional rods are
needed, please contact the place of purchase to order more. Feed the fixture
wires from posts (I) into rods (H). Pull the wires until taut. 4. Thread the
rods together to secure. Secure rods onto the fixture frame by twisting the
bottom of the rods (H) onto post (I). Twist the top of the rods (H) into the
threads of swivel post. Pull the fixture’s wires through swivel and canopy
(F). Trim the wires to the desired length adding at least 8 to 10 inches of
wire.
CONNECTING THE WIRES
5. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
INSTALL WITH SHADES REFER TO DIAGRAM (1): 6. Push canopy (F) up to the
ceiling until mounting screws (A) protrude from the holes in the canopy(F).
Thread deco nuts (G) onto the exposed threads of mounting screws (A) until
snug against the ceiling to secure. Tighten until the canopy (F) is snug
against the ceiling. Spread the arms (J) out evenly. 7. Slide candle sleeves
(L) over the sockets (K) found on arms (J). Adjust candle sleeves (L) to sit
as straight as possible. Install light bulbs (not included) in accordance with
the fixture’s specifications. Do not exceed the maximum recommended wattage.
Slide shades (N) over the installed light bulbs. Your installation is now
complete. Turn on the power and test the fixture. TO INSTALL WITHOUT
SHADES REFER TO DIAGRAM (2): 6. Push canopy (F) up to the ceiling until
mounting screws (A) protrude from the holes in the canopy (F). Thread deco
nuts (G) onto the exposed threads of mounting screws (A) until snug against
the ceiling to secure. Tighten until the canopy (F) is snug against the
ceiling.
Spread the arms (J) out evenly. 7. Slide candle sleeves (L) over the sockets
(K) found on arms (J). Adjust candle sleeves (L) to sit as straight as
possible.
Install light bulbs (not included) in accordance with the fixture’s
specifications.
Do not exceed the maximum recommended wattage. Your installation is now
complete. Turn on the power and test the fixture. 
Get help, quick tips, and explore curated content
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>