BRANDMOTION FLTW-1000 1080p Heavy Duty AHD Camera User Manual

BRANDMOTION FLTW-1000 1080p Heavy Duty AHD Camera

Product Information

Specifications

• Product Name: Heavy Duty AHD Camera 1080p FLTW-1000
• Vehicle Application: Universal
• Part Number: FLTW-1000
• Kit Contents:
  • 1x Heated HD Camera
  • 1x 20m 4-Pin Extension Cable
  • 1x Allan Key
  • 1x 3M Tape Pad

Product Usage Instructions

Camera Mounting & Power

Part 1: Universal Camera Mounting

1. Remove the 4 Allen screws that are located on the sides of the camera. Then remove the camera mounting bracket and visor.
2. Find an appropriate place to mount the backup camera. Line up the foot bracket to ensure there is enough space to attach the camera to the body.
3. Attach the mounting foot using either self-tapping screws or a bolt and nut.
4. Use a 1 hole saw to drill a hole for the camera harness.
5. Feed the harness through the drilled hole, fit the grommet to the inside of the hole. Use sealing agents if necessary.
6. Reattach camera and visor to the mounting bracket, ensuring correct orientation.

Part 2: Universal Camera Power Connection

1. The camera will be powered via a 4-pin Aviator harness. Connect
   the camera to the harness to draw the necessary power and video signal.

Camera Options

Part 3: Camera Settings

1. On the end of the camera connector, there are a WHITE and a GREEN loop wire.
2. GREEN turns on or off parking lines. Unplug the loop cap to enable parking lines.
3. WHITE turns on or off mirrored image. Unplug the loop cap to unmirror the image. – Rear-facing camera: plug in the loop cap. – Front-facing camera: unplug the loop cap.

FAQ

Frequently Asked Questions

• Q: What tools are recommended for installation?
  A: Screwdriver, Drill, Hole Saw, Electrical Tape.

• Q: How long does installation take?
  A: Installation time is approximately 1 hour 30 minutes to 2 hours.

• Q: How can I get technical support?
  A: You can call the Brandmotion technical support line at 734-619-1250 or visit their website for assistance.

Heavy Duty AHD Camera 1080p
FLTW-1000

Install Time
1hr 30m – 2hr
Questions? Call the Brandmotion technical support line at 734-619-1250 or  CLICK HERE

Kit Contents

Recommended Tools
Components for installing the FLTW-1000

Kit Contents:

1x Heated HD Camera
1x 20m 4-Pin Extension Cable
1x Allan Key
1x 3M Tape Pad

Camera Mounting & Power

1. **** Remove the 4 Allen screws that are located on the sides of the camera. Then remove the camera mounting bracket and visor.
2. **** Find an appropriate place to mount the backup camera. Line up the foot bracket to ensure that there is enough space to attach the camera to the body.
3. **** Attach the mounting foot using either self- tapping screws or a bolt and nut. Use a 1” hole saw to drill a hole for the camera harness.
4. **** Feed the harness through the drilled hole, fit the grommet to the inside of the hole.
5. Depending on the installation, the grommet may not be water tight. Use of silicone or other sealing agents is always recommended.
6. **** Reattach camera and visor to the mounting bracket. Install so the microphone is on the right when facing you to install upright.

| ****

Part 2| Universal Camera Power Connection

The camera will be powered via a 4-pin Aviator harness. Connect the camera to the harness to draw the necessary power and video signal.

| ****

Camera Options

1. **** On the end of the camera connector, there are a WHITE and a GREEN loop wire.
2. **** GREEN turns on or off parking lines.
3.   Unplug the loop cap to enable parking lines.
4. **** WHITE turns on or off mirrored image.
   •  Unplug the loop cap to unmirror the image
   •  If using as a rear facing camera, plug in the loop cap.
   •  If using as a front facing camera, unplug the loop cap.

| ****

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>