COUNTYLINE SFE-500/45W-B 18 in. Wall Mounted Barn Fan Instruction Manual
- June 7, 2024
- COUNTYLINE
Table of Contents
USER MANUAL AND OPERATING INSTRUCTIONS
18 in. WALL-MOUNTED BARN FAN
SKU NO 1025507 MODEL NO.:SEE-500/45WLO
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE USE
IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY.
SERVICE OR USE OF THIS FAN. FAILURE TO COMPLY WITH THESE INSTRUCTIONS COULD
RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE
PACKAGE CONTENTS
PART | DESCRIPTION | QUANTITY |
---|---|---|
1 | FRONT GUARD | 1 |
2 | BLADE | 1 |
3 | KNOB | 2 |
4 | REARGUARD | 1 |
5 | MOTOR | 1 |
6 | SWITCH BOX WITH CABLE | 1 |
1 | WAIL BRACKET | 1 |
8 | SCREW ST 5.9 X 60 | 1 |
9 | WASHER 06 X 016 | 1 |
10 | WALL ANCHOR 08 X 60 | 1 |
11 | SCREW ST 9.5 X 65 | 1 |
12 | WASHER 010 X 020 | 1 |
13 | WALL ANCHOR 012 X 60 | 1 |
** _SAFETY INFORMATION
_**
WARNING:
- THIS UMT IS DESIGNED FOR INDOOR USE ONLY. DO NOT EXPOSE TO ELEMENTS OR ALLOW TO BECOME VVET.
- T0 GUARD AGAINST ELECTRIC SHOCK WHILE OPERATING, DO NOT ALLOW FAN TO COME IN CONTACT WITH OTHER GROUNDED OBJECTS SUCH AS PIPES, RADIATORS. ETC.
- T0 REDUCES THE RISK OF ELECTRICAL SHOCK.
- DO NOT USE WITH ANY SOLID-STATE SPEED CONTROL ORAL 4.00 NOT USE TO EXHAUST HAZARDOUS CHEMICALS OR USE NEAR ANY FLAMMABLE LIQUIDS OR GASES AS SPARKS FROM MOTOR MAY IGNITE FUMES.
- TUR/1 OFF. UNPLUG MN AND WAIT FOR THE FAN TO STOP BEFORE MOVING. STORING. AND/OR CHANGING OPERATING LOCATIONS.
- DO NOT INSERT YOUR HAND OR OTHER OBJECTS INTO THE GUARD OR THE MOVABLE PARTS.
- BEFORE OPERATING ALWAYS CHECK THE FAN FOR LOOSE OR DAMAGED PARIS.INSPECT THE POWER CORD FOR ANY DAMAGE. NEVER USE RN F ANY PARTS ARE DAMAGED OR MISSING. TREVER USES FAN IIIINOUT SAFETY GUARDS ATTACHED.
- WHEN USED WITH All EXTENSION CORD. USE ONLY CORO OF PROPER SIZE (AMP RATING). UL LISTEO.A110 WITH RECEPTACLE TO ACCEPT INREE PRONG GROUNDED PLUG FURNISHED ON THE FANS POWER CORD. ALWAYS KEEP POWER CORD ANO EXTENSION CORDS AWAY FROM HEAT. Ell, AND SHARP EDGES. INSPECT CORDS PERIODICALLY AND REPLACE IF DAMAGED.
- DISCOIINECT FANS FROM POWER SOURCES WHEN NOT IN USE. BEFORE SERVING AND WHEN MINING OR REPAVING.
- REPAIR OF THIS APPLIANCE SHOULD BE DONE BY A DUNI-FED RECRUIT.
- 14 CASES OF POWER FAILURE. TURN FAN Off AT POWER KNOB OR CHAN TO PREVENT UNEXPECTED RESTORING AND COMPONENT DAMAGE.
- KEEP CHILDREN AWAY FROM FAIL AT ALL TIMES.
- DO NOT USE A HIGH-PRESSURE HOSE TO SPRAY THE RN FOR CRANING.
- DO NOT OPERATE ANY RN WITH A DAMAGED CORD OR PLUG. DISCARD FAIT OR RETURN TO AN AUTHORIZED OAR FACULTY FOR EXAMINATION AND/OR REPAIR.
- DO NOT RUN CORO UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS. OR SIMILAR COVERINGS. DO NOT ROUTE THE CORD UNDER FURNITURE OR APPLIANCES. PLEASE ARRANGE CORO AWAY FROM TRAFFIC AREA ANO WHERE IT WILL NOT BE TRIPPED OVER.
CAUTION:
- PRIOR TO CLEAVING. UNPLUG THE FAN FROM THE SOCKET.
- DONOT RUAERSE THE FAN IN WATER.
- RT THE GUARD ONTO THE FAN BEFORE STARTING UP THE RN. 4. SUPERVISE CHILDREN TO ENSURE THEY GO NOT PLAY WITH THE RN.
CARE AND MAINTENANCE
UNPLUG THE APPLL1NCE BEFORE CLEAVING. DON’T USE ANY WATER FOR CLEANING METAL SURFACES. SLIGHTLY MOISTEN A CLOTH AND THEN WIPE OFF THE SURFACES OF THE FAN. IN ORDER TO REMOVE THE DUST FROM THE PROTECTIVE GUARD, USE A VACUUM MEATIER OR REMOVE THE FRONT PROTECTIVE GUARD BY REMOVING THE SECURING SCREW ON THE EDGE OF THE GUARD WITH A SCREWDRIVER. AFTER CLEANING, REMOUNT THE SAFETY GUARD. AFTER DOING THIS. FASTEN THE SECURING SCREW ON THE EDGE OF THE PROTECTIVE GUARD.
SAVE THESE INSTRUCTIONS
OPERATING INSTRUCTIONS
- ADJUST THE DESIRED SPEED BY PULL CHAN SWITCH WITH 3 SPEEDS CONTROL 0 – STOP 1 -LOW 2 – MEDIUM 3 – HIGH
- TILT OR DOWN THE FAN HEAD FOR CHANGING AIRFLOW DIRECTION.
WALL MOUNT ASSEMBLY INSTRUCTION
- MARK THE DESIRED HOLE LOCATIONS BY USING THE WAU. BRACKET, AND THEN DRILL HOLES.
- FOR CONCRETE WALL INSTALLATION, AFTER DRILLING, INSERT THE WALL ANCHORS AND TAP THEM FLUSH WITH THE WALL. POSITION THE BRACKET AND THEN SCREW THE TWO BOLTS INTO THE ANCHORS. SECURELY ATTACHING TO THE WALL.
- FOR WALL STUD INSTALLATION. AFTER DRIVING THE SMALLER DIAMETER PILOT HOLE. POSITION THE BRACKET AND SCREW THE TWO BOLTS INTO THE WALL UNTIL THEY ARE SECURED.
CAUTION: THE FAN IS ONLY SUITABLE FOR CONCRETE WALLS AND WALL STUDS. DO NOT USE FOR DRYWALL MOUNTING. USE THE MOUNTING ACCESSORIES SHAPED WITH PRODUCTS FOR WALL MOUNTING.
NOTE: FOR LONGER PARTS LIFE, AFTER 10 HOURS OF CONTINUOUS OPER/MON. TURN THE FAN OFF FOR 15 MINUTES TO ALLOW THE MOTOR TO COOL.
TROUBLESHOOTING GUIDE
PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
---|---|---|
THE FAN FAILS TO OPERATE | 1. FAN MAY NOT BE PLUGGED IN. | 1. MAKE SURE THE |
FAN IS PLUGGED IN AND THE ELECTRICAL OUTLET IS WORKING PROPERLY
2. SOMETHING MAY BE OBSTRUCTING THE FAN.| 2. CHECK FOR ANY OBSTRUCTION. IF
YOU FIND AN OBSTRUCTION, TURN THE FAN “OFF”. UNPLUG THE FAN AND CAREFULLY
REMOVE THE OBSTRUCTION. PLUG THE FAN IN AND TURN IT ON AGAIN, REFERRING TO THE
OPERATION INSTRUCTIONS.
TECHNICAL DATA
MODEL NO.| BLADE DIA. SIZE| VOLJ Hz| SPEED| INPUT
POWER
---|---|---|---|---
SFE-500/45W-B| 18 IN./450MM| AC 120V /60 Hz| HIGH
MEDIUM
LOW
| 124W
110W
100W
Distributed by:
TRACTOR SUPPLY COMPANY
5401 VIRGINIA WAY,
BRENTWOOD, TN 37027
For customer support, call:
1-888-376-9601
www.TractorSupply.com
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>