OTO ZB-6000 Magnetic Bike User Manual
- June 12, 2024
- OtO
Table of Contents
OTO ZB-6000 Magnetic Bike
Safety Instructions
- People with the following conditions should consult their physician before using the product:
- Who uses a medical electronic device, which is embedded in the body, such as a pacemaker.
- Who suffers from heart disease.
- Who suffers from backbone injury or disease.
- Who is suffering from bone fragility, especially on the backbone.
- After surgery.
- Who is pregnant or in a period of monthly illness.
- Who suffers from malignant tumors.
- Who is suffering from osteoporosis.
- Who has problems with blood circulation.
- Who is suffering from skin disease or infection.
- Who is undergoing medical treatment or feels some physical abnormality previously or is being treated now.
- Who has some abnormality or deformity of limbs or backbone.
- Who has diseases, injuries due to illness or accident.
- If the product is damaged, do not try to repair the product. This must be handled by OTO technician or the product guarantee will become void.
- Children should not use this product. They should be under supervision to ensure that they will not treat this product as a toy.
- Do not use the product if cover is damaged or if there is a mechanical or electronic failure. Please contact OTO or its authorised dealers.
- Only use or place the product in accordance with the instructions in this user manual.
- Do not use this product in high temperature conditions or beside hot objects such as heaters, stoves. This product is intended for household use only.
- Avoid using the product immediately after eating. Wait for at least an hour before using the product.
- Make sure seat is suitably adjusted and securely fastened.
- Strap legs onto the pedals to prevent slippage during use.
- Be careful when folding the bike and remember to lock with the safety pin.
- Make sure the bike is in folded position and locked while moving.
- Do not put the bike in a humid environment.
- Wipe the bike especially the handlebar after exercise. This will protect the cosmetic of the bike.
- The magnetic mechanism installed in the bike is a patented technology. Do not try to open the housing or repair the bike yourself.
- Wear appropriate attire for the exercise. Remove loose items especially those on the leg.
- Start with some warm-up exercise before commencement.
- Always start with low resistance and then gradually increase.
- Make sure exercise environment is airy. Breathe normally during exercise. Stop if feel uncomfortable.
- 30 minutes normal speed cycling is recommended for a complete workout. A
Parts Name
Parts List
Assembly
STEP 1
-
A.) Pull out the lock pin (#24) from the main frame (#1) and adjust the main frame to the correct position.
Insert the lock pin (#24) back to the main frame (#1). [Figure A]
-
A.) Pull out the lock pin (#31) and pull the front support tube (#3) forward.
Insert the lock pin (#31) into the main frame (#1) and then fasten it with a club knob (#30). [Figure B]
STEP 2
Locate the rear base tube (#9),
- two M8x65 carriage bolts (#14),
- two M8 (φ22) washers (#17) and two M8 cap nuts (#22).
- Insert carriage bolts (#14) through rear base tube (#9) so that bolts protrude through the top side of the base tube.
- Mount body frame (#1) over the protruding carriage bolts.
- Place one washer (#17) over each carriage bolt, resting the washers on top of the body frame.
- Place one cap nut (#22) on each carriage bolt and tighten securely.
STEP 3
Locate the front base tube (#8),
- two M8x65 carriage bolts (#14),
- four M8 (φ22) washers (#17) and two M8 cap nuts (#22),
- two M8x15 allen bolts (#16).
A.) Insert carriage bolts (#14) through front base tube (#8) so that bolts protrude through the top side of the base tube.
- Mount body frame (#1) over the protruding carriage bolts.
- Place one washer (#17) over each carriage bolt, resting the washers on top of the body frame.
- Place one cap nut (#22) on each carriage bolt and tighten securely. DO NOT FULLY TIGHTEN IT.
STEP 4
Locate pedals (#5/#13).
- Insert pedal stamped ”R” into the Right crank arm and tighten securely.
- Insert pedal stamped ”L” into the Left crank arm and tighten securely.
NOTE: If pedals are inserted into the wrong crank arm, they will likely be damaged during use.
STEP 5
Locate handlebar (#7).
- Connect the upper sensor wire (#28) to the monitor (#27).
- Place handlebar (#7) on top of main frame.
- Place three M8 Screw (#16) and washers (#18) in each hole on handlebar and tighten securely
STEP 6
Locate seat (#11) and seat post (#4).
- Mount the seat (#11) onto the seat post (#4) and tighten themsecurely with three nuts (#26) and flat washers (#18)
STEP 7
To set the seat.
- Insert the seat post (#4) to the main frame and fasten it with a lock knob (#23).
STEP 8
-
A.) Attach the back support tube (#6) to the seat post (#4), tighten with two sets of carriage bolts (#15), flat washers (#19), nylon nuts (#26).
Attach the side handlebar (#10) to the back support tube (#6), tighten with two sets of carriage bolts (#15), flat washers (#19) and domed nuts (#22). Then insert the lock pin (#33) into the back support tube (#6). -
B.) Attach the back cushion (#12) to the back support tube (#6), fasten with four sets of allen bolts (#20), spring washers (#21).
STEP 9
You could fold this bike as follows when you don’t want to exercise
- Pull out lock pin (#33), fold down the back cushion (#12), and store the lock pin back to the hole. STEP 9
- Pull out the lock pin (#24) from the main frame (#1) and fold the main frame (#1) to a proper position, then insert the lock pin (#24) to fasten the main frame (#1).
- Loosen the club knob (#30) in counter-clockwise direction and pull out the lock pin (#31). Then fold the front support tube (#3) to a proper position and insert the lock pin (#31) to the main frame (#1).
How To Operate
Monitor :
- MODE/RESET: Press to select functions. Press and hold for 3 seconds to reset time, distance and calories, etc.
- SCAN: Press MODE button until “▼” appears at SCAN position. The monitor will rotate through the following functions: Time, Speed, Distance, Calories, Odometer, and Pulse. Each display holds 4 seconds.
- TIME: Count the total time from exercise start to end.
- SPEED: Display current speed.
- DISTANCE: Count distance from exercise start to end.
- CALORIES: Count the total calories burnt from exercise start to end.
- ODOMETER: Count the total distance from the time when the batteries are installed to the time when they run out.
- PULSE: Show the pulse rate when the user holds the sensors for at least 3 seconds.
NOTE :
- If the display is faint or shows no figures, please replace the batteries.
- The monitor will automatically shut off if there is no signal received after 2 minutes.
- The monitor will be auto powered on when starting to exercise or pressing button.
- When you stop exercising for 4 seconds, the display will stop calculating and a ”STOP” will be displayed on the screen. When you start exercising, the display will automatically start calculating and the ”STOP” will disappear.
Bike :
- RESISTANCE ADJUSTMENT: Turn the “Resistance Adjustment” knob clockwise (+more) to increase resistance; anti-clockwise (-less) to lessen the resistance.
- SEAT ADJUSTMENT: Unlock the “Seat Adjustment” knob by turning anti-clockwise and pull it to adjust seat level. Turn clockwise to lock the knob after securing the position.
Product Specifications
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>