SEURA Miro Lighted Mirror User Manual

Miro Lighted Mirror

“`html

Product Information

Specifications:

• Product Name: Artisan Collection Miro Lighted Mirror
• Installation: Professional installation recommended
• Manufacturer: Seura
• Website: www.seura.com
• Address: 1230 Ontario Road, Green Bay, WI 54311

Product Usage Instructions

Storing the Unit:

After inspection, repack the unit securely to keep it safe until
installation.

Removing the Unit from the Box:

Carefully lift each item out of the box. Lift the mirror by the
brackets attached to the back of the mirror glass. Do not pull the
unit out by the frame if it has one. Lay the mirror flat or upright
against a sturdy wall with foam protectors in place.

Important Note:

Do not remove any reflective or white tape on the mirror or
mirror housing as it is not part of the packaging and removing it
may damage the product.

Installation Safety Precautions:

Read all instructions and review the drawing package before
installation. Always follow basic safety precautions to reduce the
risk of fire, electric shock, or injury.

Parts Included:

The box should contain mounting hardware, self-drilling drywall
anchors and screws, and the Miro Lighted Mirror. Check for
completeness before use.

Tools Required (not included):

• Anchors for concrete or wood screws
• Cables (for hard-wire configuration)
• Level, protective eyewear, stud finder, measuring tape, pencil,
  Phillips #2 screwdriver, wire cutter, wire stripper, drill

Installation Process:

Turn off main power at the circuit breaker before installation.
Ensure the power cable is on a switched circuit for controlling
mirror lights. Use 3 conductor wire (Black=Live, White=Neutral,
Green=Ground) and adjust wire length if needed.

Frequently Asked Questions (FAQ)

Q: Do I need professional installation for this mirror?

A: Professional installation is recommended to ensure proper
setup and safety.

Q: Can I remove the adhesive or white tape on the mirror?

A: No, do not remove any tape on the mirror or mirror housing to
avoid damaging the product.

Q: What should I do if some parts are missing from the

box?

A: Contact customer support at 1-800-957-3872 for assistance
with missing parts.

“`

USER MANUAL
ARTISAN COLLECTION MIRO LIGHTED MIRROR
PROFESSIONAL INSTALLATION RECOMMENDED
WARRANTY REGISTRATION
REGISTER FOR EXTRA BENEFITS
Activate within 30 days of purchase: seura.com/activate
1-800-957-3872 1230 ONTARIO ROAD, GREEN BAY, WI 54311
W W W.SEUR A .COM

Thank you for selecting a Séura Lighted Mirror.
Please read this guide before beginning installation.

Carefully remove and inspect the unit for possible damage that occurred during shipping. If there is damage, please call Séura at 1-800-957-3872. If your shipment is damaged and is not noted on the delivery receipt, Séura cannot guarantee compensation. All freight damage claims must be reported to Séura Customer Service within 48 hours of delivery to be covered by our warranty.

How to properly store the unit until installation
After inspection, repack the unit so it stays safe and protected until installation.

How to properly remove the unit from the box
Carefully lift each item out of the box. Lift the mirror by the brackets attached to the back of the mirror glass. If the mirror has a frame, do not pull the unit out of the box by the frame as the frame may detach from the mirror. Lay the mirror glass flat or upright against a sturdy wall with the foam protectors remaining on the unit.
If the mirror or mirror housing contains reflective tape or white tape, do not remove it. Adhesive tape is used on some models and is not part of the packaging. Removing the adhesive will damage the product.

Séura Lighted Mirrors use LEDs that are rated to retain 70% overall brightness and the end of life, including cases where an individual LED fails.

WARNING: READ ALL INSTRUCTIONS AND REVIEW THE COMPLETE DRAWING PACKAGE BEFORE ATTEMPTING TO INSTALL OR SERVICE THIS PRODUCT.

When installing and during use of this product, basic safety precautions should always be followed to reduce the risk of fire, electric shock and/or injury to persons including the following:
· Make sure the installation area is free of clutter.
· Do not place the product on an unstable cart, stand, tripod or table.
· To avoid damage to the mirror, only transport it in a vertical position. Transporting the product horizontally may permanently warp the mirror.
· Inspect the desired location for installation and be aware of all electrical wiring pathways, water pipes, gas lines, or other potentially hazardous conditions that may exist to protect from accidental damage.
· Ensure all required electrical specifications are adhered to and have been installed by the appropriate

individuals and are code approved.
· Ensure all framing requirements, if needed, have been completed to building code and pose no structural issues.
· It is highly recommended that at least two (2) people assist in the installation of the mirror.
· Only qualified individuals should attempt to service the product.
· Close adult supervision is necessary when any product is used by or near children.
· Protect against electric shocks and burns by wearing safety gloves.
· Do not operate any product with a damaged cord or plug or operate it after the appliance malfunctions or has been damaged in any manner.
· Do not let the power cord or wiring come in contact with hot surfaces such as radiators, heat registers, stoves, or other

products that produce heat.
· To protect against electric shock, do not immerse the power cord, power plug, or product in water or other liquid.
· This product is only intended for use indoors.
· This product is not waterproof. Do not immerse this product in water or expose to dripping or splashing water as this could cause an electrical hazard.
· In damp locations, it is REQUIRED that the plug-in version of this product is plugged into an electrical outlet protected by a Ground Fault Circuit Interrupter (GFCI) to protect against electric shock, fire, and/or injury. Failure to do so will void any warranty for this product.
· The product must have proper, correct and sufficient AC supply voltage.
· Retain this manual in a safe place for future reference.

WARNING: Cancer and Reproductive Harm: www.p65warnings.ca.gov.

Parts Included
Before using the device, please check the following contents of the box for completeness. Illustrations are not to scale. Additional parts may be included for custom mirror upgrades.

Mounting Hardware
Self-Drilling Drywall Anchors and Screws
(for use when mounting into drywall and not wall studs; quantity varies by mirror size and may include extras)

A:AM: 6Mx6 3x53m5 mmm
Miro Lighted Mirror
B:B1:41m4 mmm

A: M6 x 35 mm

WARRANTY REGISTRATION
REGISTER FOR EXTRA BENEFITS
Activate within 30 days of purchase: seura.com/activate

A: M6 x 35 mm

Product Manuals

Access product set-up and installation instructions, product specifications, warnings and safety information, product warranty, and additional product information.

www.seura.com/manuals

Open and Scan

A: M6 x 35 mm

Manual with installation instructions unique to your mirror

B: 14CmC:mM: 8M8

B: 14 mm C : M8B: 14 mm

Parts and Tools Required (not included)

or oénton cnocnrectroeto

D:EC:EoM:n8Mcrx8e6txe56Am5nmmchmor Ancrages de béton

FD:F:M:C6Mon/6cM/re8Mte8E:AMnc8hxor65Dm:GCm:Go5n: cm5remmtemAnFc:hEMo:r6M/8Mx865 mm Ancrages de béton Ancrages de béton

EG::M5F8:mMxm65/ Mm8m

Anclajes para concreto WAhnipcl/ajHeasrdp-aWrairecoEnleccrterAticonacl lajes paWrairecoNnuctrseto 4+ Wood Screws

Cables (required for hard-wire configuration)

(required if mounting into wall studs)

F: MG6: 5/ Mm8m

Level

Protective Eyewear

Stud Finder

Measuring Tape

Pencil

Phillips #2 Screwdriver

Wire Cutter (required to reduce the length of the
whip)

Wire Stripper

Drill

Installation
IMPORTANT: TURN OFF MAIN POWER TO THE INSTALLATION LOCATION AT THE CIRCUIT BREAKER.
Step 1: Prepare proper wiring and wall switch. · Turn off the main power before installing the fixture in order to prevent possible electric shock. Locate the circuit breaker
control for the room where you’ll be working and switch the circuit to off. · A whip is required for hardwire installation. In other words, you need access to a power cable that comes from a Junction Box
in the wall. The power cable should be on a switched circuit to allow for control of the mirror lights. These extra wires are prewired together. Ensure that you are using 3 conductor wire (Black=Live, White=Neutral, Green=Ground). Make sure the length of the whip is long enough to reach from the power box in the wall to the mirror. If the whip is longer than needed, you may choose to use a wire cutter to reduce the length.
IMPORTANT · Mirrors that include Touch Control functionality require the junction box circuit to be a constant
hot circuit and not a switched circuit. · Mirrors that include a Defogger (non-touch controlled) can be wired three different ways:
1. On the same switch as the mirror lights: When the mirror lights turn on, the defogger turns on. This requires the junction box circuit to be a switched circuit.
2. On a separate switch from the mirror lights: One switch will control the mirror lights and a separate switch will control the defogger. This requires the junction box circuit to have separate switched circuits, one for the mirror lights and one for the defogger.
3. Always on, no switch required: The defogger will remain on, even when the mirror lights are off. This requires the junction box circuit to be split with one side constant hot (for the defogger) and one side that is switched (for the mirror lights).
· If your mirror includes dimming capability but does not include the optional Dimmable Touch Button upgrade, verify that your wall switch supports dimming functionality. The dimmable switch must be 0-10V or Triac based on the configuration of your personalized mirror.

Step 2: Map out the installation area and mount the lighted mirror housing to the wall. · Align the mirror housing on the wall. Using the keyhole at the top center, mark and drill the hole. If mounting on drywall, insert
the provided wall anchors using a hammer. This step can be omitted if mounting into studs.
*Remove the security screw to detach the mirror from the housing.

· After securing the mirror housing to the wall with a screw, mark the outermost hole in each corner. Next, remove the mirror housing and drill holes for the provided wall anchors. Install the wall anchors, then rehang the mirror housing and secure it by screwing in all the corners.

Step 3: Make wiring connections.
· Séura lighted mirrors are equipped with an easy-to-install wiring fixture disconnect that can be found on the mirror housing that is now connected to the wall. Refer to your included drawing package to identify the location of the fixture disconnect.
· Connect the whip (extra wires that are pre-wired together) from step 1 to the fixture disconnect. The connection accepts AWG 16 – 12 solid or stranded (19 strands maximum). Using a wire stripper, strip the insulation on the wires back approximately 1/2″.
· Open the fixture disconnect by pushing down on the tab that connects the top and bottom pieces. Connect wires into the fixture disconnect using the color code diagram pictured. Reconnect the top and bottom pieces by sliding them together.
· If using a 0-10V dimmable switch, then connect 0-10V dimming signal directly to the driver dimming control wires.
· Turn the wall switch to on and verify functionality. If on a constant hot circuit, power will be delivered immediately when the circuit breaker is turned back on.
Wiring For Units With 0-10V Dimming

Wiring Fixture Disconnect
Wiring connections made by the manufacturer
Field wire connector Connections to be made by the installer in the field
Neutral (White) Ground (Green) Line Voltage/Hot (Black)

0-10V Dimming Control Wire (Negative)
0-10V Dimming Control Wire (Positive)

Step 4: Hang the mirror
· Hang the mirror onto the housing by positioning the mounting brackets on the back of the mirror so they rest on top of the brackets on the housing. Start by holding the mirror slightly higher than the housing and slowly lower the mirror until the mirror brackets rest on the housing brackets.
· Tuck any extra wire into the wall behind the mirror so it’s no longer visible.
· Ensure the brackets are interlocked and the mirror is secure by making sure the mirror is level and evenly spaced from the wall.

Installed Interlocking
Brackets

Care and Maintenance
Séura’s mirror glass coatings have been developed to protect the mirror surface and allow easy maintenance. Please follow the guidelines listed for proper mirror care and cleaning: · The glass surface should be cleaned with any conventional non-ammoniated glass
cleaner. Do not use any acid, alkali, or ammonia cleaners. · Care should be taken to use only a soft lint-free cloth. Apply all cleaners directly to the
cloth and not the mirror surface. Never saturate the mirror surface as residual cleaner may seep behind the mirror. Do not allow the mirror edges to remain wet. · Stubborn spots can be removed with solvents such as mineral spirits, de-natured alcohol, and acetone. Immediately remove solvent and dirt residues per the prescribed methods above with a compatible glass cleaner or water. · Take care when moving the mirror or accessories near the edges of the mirror. Exposed polished edges of glass are susceptible to chipping when in contact with other hard surfaces such as a faucet or metal soap dispenser. Decorative frames should be cleaned using a clean, soft cloth to wipe dust and dirt off.

References

• Activate – Séura
• p65warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>