SEURA IWT-27 Hydra Indoor Waterproof Television User Manual

SEURA IWT-27 Hydra Indoor Waterproof Television

WARNINGS

To reduce the risk of fire, electrical shock and other injuries, keep these safety precautions in mind when installing, using, and maintaining your Television. The socket-outlet should be installed near the equipment and be easily accessible. The TV should be connected to a grounded GFCI protected main socket outlet.
WARNING: If you manipulate against the recommended usage, serious injury or death to user may result.

• To protect against electric shock, do not immerse the power cord, power plug, or product in water or other liquid.
• Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.
• Close adult supervision is necessary when any product is used by or near children.
• Do not operate any product with a damaged cord or plug or operate it after the appliance malfunctions or has been damaged in any manner.
• Do not use the product close to any heat sources such as radiators, heat registers, stoves, or other products that produce heat.
• Do not let the power cord come in contact with hot surfaces.
• If you notice any smoke or scorched smell near the product, unplug power cord and refer to qualified personnel for service and/or repair.
• Do not use or place any combustible or flammable substances near the product.
• To electrically disconnect the product, turn OFF the product, then remove the electrical power plug from the outlet.
• Do not place heavy articles on or step on the product.
• Do not place the product on an unstable cart, stand, tripod or table.
• Do not use this product for other than intended use. This Séura product is only intended for use indoors.
• For added safety during a lighting storm, or when this product is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna.
  NOTE: THE POWER SUPPLY MUST NOT BE MOUNTED INSIDE A WALL CAVITY.
  Specifications of this product are subject to unannounced changes; this manual may thus not reflect the current technical status.

WARNING: READ ALL INSTRUCTIONS AND REVIEW ALL DRAWING SHEETS BEFORE ATTEMPTING TO INSTALL OR SERVICE THIS PRODUCT.
When installing and during use of this product, basic safety precautions should always be followed to reduce the risk of fire, electric shock and/or injury to persons including the following:

• I inspect the desired location for installation and be aware of all electrical wiring pathways, water pipes, gas lines, or other potentially hazardous conditions that may exist to protect from accidental damage during creation of on-site conditions.
• Ensure all required electrical specifications are adhered to and have been installed by the appropriate individuals and are code approved.
• Ensure all framing requirements, if needed, have been completed to building code and pose no structural issues.
• I t is REQUIRED that this product is plugged into an electrical outlet protected by a Ground Fault Circuit Interrupter (GFCI) to protect against electric shock, fire, and/or injury. Failure to do so will void any warranty for this product.
• Only qualified individuals should attempt to service the product. Removing covers can expose you to high voltage and other dangerous conditions.
• Do not let the power cord come in contact with hot surfaces.
• To electrically disconnect the product, turn OFF the product, then remove the electrical power plug from the outlet.
• Do not use this product for other than intended use.
•  This Séura product is only intended for use indoors.
• Retain this manual in a safe place for future reference.

**Safety Warning

**

Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as:

• Using cabinets or stands recommended by the manufacturer of the television set.
• Only using furniture that can safely support the television set.
• Ensuring the television set is not overhanging the edge of the supporting furniture.
• Not placing the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television set to a suitable support.
• Not placing the television set on cloth or other materials that may be located between the television set and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the television set or its controls.
  If your existing television set is being retained and relocated, the same considerations as above should be applied.

2-Part Product Anatomy

BACK BOX

TV ASSEMBLY

Display Requirements

Operation and Storage Requirements
The ambient temperature for operating the device is between 41 to 122 degrees Fahrenheit. Do not install the device in the proximity
of heat sources, such as heating pipes, heaters, furnaces or other devices that radiate heat. Mount the device in such a way that it is protected against moisture. Trouble-free operation is ensured up to 100% air humidity. To prevent fire or electric shock, never allow liquids to enter the unit. The product must be stored in dry and well-ventilated rooms, without extreme temperature fluctuations. Heat sources and aggressive active substances may not be stored in the proximity of the device. The required storage temperature is 32° F – 140° F at an air humidity of 5 – 85% RH non-condensing. The device must be stored in the complete packaging, as delivered. The product must not operate on average more than twelve (12) hours per day on a permanent or extended periodic basis. The product must have proper, correct and sufficient AC supply voltage.

Installation Environment
Avoid direct light or sun exposure, direct proximity to heat sources, outdoor installation. The product is specifically designed for indoor use only. There is the danger of fire and of electric shock and damage to the device if it is operated outdoors. Do not place any heat sources such as radiators and heat registers, etc. near the monitor. To reduce eye strain, avoid installing the Séura Television against a bright background such as a window. Position the monitor at the height of your eye level. Position the monitor directly in front of you at a comfortable viewing distance.

Installation
Have this product installed by qualified personnel only. Use the mounting systems which are specified or recommended by Séura. Install the product in a way that it is fixed properly and take care that children are not exposed to danger. Please take extra care during installation, avoid impacts. Before cabling your monitor, check that the power is off. To avoid any possibility of electric shock, always connect your equipment to properly grounded outlets. Use of power cords or adapters other than those provided may cause fire or malfunction. Place this product as close to the power socket as possible. Leave enough space to insert and remove the power plug on demand. Even if you switch off the product with your remote control, power is not cut off unless the power cord is unplugged.
The device may only be operated with the provided power adapter. The rated voltage is indicated on the product label. The device is factory-set to the optimal operating voltage (see Technical Specification). Use only power cords and plugs that are suitable for your local electrical outlets. Install the power cords in such a way that it does not obstruct anyone. Ensure furthermore that the cable is not clamped and that it cannot be pulled out accidentally from the power adapter. Do not install the power cords in the proximity of heating elements and never place heavy items on the cable or power adapter. Do not modify or arbitrarily repair the power cords.

CAUTION
Do not use any power cords or adapters other than those provided with this product! Use of power cords or adapters other than those provided with this product may cause fire, electric shock or malfunction. If several kinds of power cords are provided with this product, use the one that fits your power socket. Do not let the adapter hang down while using. Do not cover or wrap the adapter. Leave space around the adapter to prevent overheating. The individual components can be destroyed, if the polarity is reversed or an incorrect connection is used. A goodwill replacement is not possible in such cases, since each device is submitted to meticulous quality inspections prior to shipping. The connecting plugs must be attached in such a way that the connector is held firmly. Have trained technical personnel install the electrical facilities necessary for mounting. The power adapter must be installed in ventilated areas due to heat emission. Connect the power cord to a grounded outlet. Never cut or damage the power cord.
Please disconnect the device from the power adapter in the following cases:

1. The device is out of use for a lengthy period.
2. The device malfunctions or displays other unusual features, necessitating maintenance work.
3. During a thunderstorm.

Please plan the positioning of the power adapter and the source cables before proceeding with the structural measures and positioning of the Séura Television. Observe the protection zones when placing the power adapter! Please bear in mind that the power adapter has to be placed beyond the inset due to heat emission.

NOTE
The power cable should be adequately secured to prevent it from becoming unstable and/or falling. Make sure the power source circuits are properly grounded. Use the supplied power cord in order to connect it to the power source. If your installation requires a different power cord, be sure to use an officially approved power cord displaying the mark of the safety agency that defines the regulations for power cords in your country.
Ensure that your installation complies with your national and local safety rules. Any servicing, adjustment, maintenance or repair must be performed only by service-trained personnel.

Setup

Before using device please check the following contents of the box for completeness:

Input/Output Overview (Bottom View)

Waterproof Remote Functions

Installation

NOTE:
All Séura drawing packages indicate generalized nominal residential wood framing construction and are not indicative of any particular building code. It is the responsibility of the installer that all electrical, audio/visual, and framing construction are code compliant to the municipality in which the product is being installed. Modifications made to Séura recommendations are at the sole discretion of the installer and release Séura of all liability. Inspect the desired location for installation and be aware of all electrical wiring pathways, water pipes, gas lines, or other potentially hazardous conditions that may exist to protect from accidental damage during creation of on-site conditions.

Ensure all required electrical specifications are adhered to and have been installed by the appropriate individuals and are code approved.
Ensure all framing requirements, if needed have been completed to building code and pose no structural issues.
It is REQUIRED that this product is plugged into an electrical outlet protected by a Ground Fault Circuit Interrupter (GFCI) to protect against electric shock, fire, and/or injury. Failure to do so will void any warranty for this product. Only qualified individuals should attempt to service the product. Removing covers can expose you to high voltage and other dangerous conditions.

Read all installation instructions before beginning installation.

• Step 1
  Install back box to framing members using the provided four screws and washers through screw-mounting slots in back box. Ensure that the front of the box is flush with finished wall and mounting tabs will rest on finished wall surface. Feed power and other desired cords through pass-through port.
  Note: Do not overtighten mounting hardware. Back box should fit snuggly between framing members. If the fit is poor, and overtightening occurs, the back box may deform, resulting in a poorly sealed installation. If the back box doesn’t fit well between framing members, shim the framing members for a square and stable fit.

• Step 2
  While keeping cord ends outside the back box pass-through port, finish the wall tight to the edges of back box, removing any gap. Once complete, the final wall surface should be flush with the front edge of the back box as shown.

• Step 3
  Install TV Assembly:

  • Place TV assembly face down on a clean, dry surface near the installed back box. Make all necessary connections and ensure LCD operation is successful.
  • Before applying adhesive, “dry fit” the TV assembly in back box. Notice that the gravity lock mounts engage. Ensure functionality in installed position.
  • Remove TV assembly from back box. Do not disconnect any wires. Clean any residue from glass and remove debris.
  • D) Generously apply 1/8″ bead of supplied waterproof sealant to glass face as close to the edge as possible. Affix to wall surface, ensuring gravity lock mounts are fully engaged. Sealant should seep out the front on all edges to provide the best seal.
  • I mmediately after TV assembly is installed and sealed, again verify the functionality of LCD and remote. If operation has been compromised by the installation, corrections can easily be made before the sealant has cured.
  • Wipe dripping or excessive sealant.
    NOTE: THE POWER SUPPLY MUST NOT BE MOUNTED INSIDE A WALL CAVITY.

• Step 4
  Allow waterproof sealant 24 hours to cure at 72 degrees Fahrenheit before exposing to moisture. (or recommended time designated by sealant instructions)
  Once fully cured, use a razor blade or utility knife to carefully remove excess sealant.

Making Connections

Connecting Video
The Television features one Component, one Composite, one VGA, one coaxial Cable/Antenna input, and two HDMI inputs. We recommend using the HDMI inputs for best video and sound quality.

Connecting Audio
Two passive loudspeakers can be connected to the speaker output socket with speaker cables. Observe the polarity (+ and -) of the connections to avoid phase errors (= incorrect stereo playback).
Note: This product is not equipped with built-in speakers.

Connecting a USB Media Source
Connect an external USB media source to the USB socket to display photos, play music or install a software update.
In order to have access to the USB port after installation we recommend installing a USB extension cable.

Connecting a Home Automation System
With the RS-232 interface (9 pin d-subminiature connector female) you can connect a serial cable for communication with a home automation system, PC, etc. The baud rate is 115200.

On Screen Display Menu (OSD)

On Screen Display Menu (OSD)
In the on screen display menu (OSD) you can adapt the characteristics of your display based on personal
preferences. OSD menus include Video, Audio, TV, Setup, and Parental.

1. Press on your remote control to open the OSD menu
2. Navigate within the OSD with the left/right and up/down arrows
3. Change settings with the left/right arrows
4. Go back one step with
5. Confirm selection with the OK button
6. Press to exit the OSD menu.

Input Source Selection
In the Input Source menu, you may select from the available input sources.

1. Press to power the Television on
2. Press to display the Input Source list OR use the quick input controls on the remote to directly designate the input source.
3. Press the up or down arrows until the desired Input Source is highlighted.
4. Press OK to confirm selection of the chosen input and clear the Input Source list from the screen or press again to switch through the signal inputs.
5. Press to close the Input Source list without selecting an alternative

Video Settings

The Video Settings menu offers options to enhance and refine the image characteristics of your Séura Television. These settings are based on ambient conditions of illumination and personal preferences.

Adjustment options include:

• Picture Mode
• Brightness
• Contrast
• Saturation
• Hue
• Sharpness
• Back Light
• Advanced Video
• Reset Picture Mode

PICTURE MODE
Within the Picture Mode menu you can customize the image display according to your preferences.
Your options: Home, Vivid, User, Cinema, Sport
The Home setting is recommended for most viewing environments. Select the User Mode to adjust your preferred settings manually.

Advanced Video Settings
The Advanced Video Settings menu offers further options to refine the image characteristics of your Séura Television.

Adjustment options include:

• DNR
• MPEG NR
• Adaptive Luma Control
• Flesh Tone
• DI Film Mode
• Blue Stretch
• Game Mode
• Blue Mute
• Gamma
• Color Temperature

COLOR TEMPERATURE
Within the Color Temperature menu you can customize the Color Temperature of the picture according to your preferences.
Your options: Standard, Warm, User, Cool

Audio Settings
The Audio Settings menu offers options to enhance and refine the sound characteristics of your Séura Television based on personal preferences.

Adjustment options include:

• Balance
• Bass
• Treble
• Sound Surround
• Sound Mode
• MTS
• Audio Language
• SPDIF Type

Setup Menu
The Setup Menu offers options to determine fundamental settings of your Séura Television based on personal preferences. Adjustment options include:

• OSD Language
• Caption
• Time Setup
• Reset Default ****
• TIME SETUP
  Options within the Time Setup selection include Time Zone, Time, and Sleep Timer.
  TIME ZONE
  The local time zone may be selected using the graphical map of North America
  SLEEP TIMER
  Within the Sleep Timer menu you can determine a timespan after which the Séura Television will turn off automatically.
  Your options: Off, 10, 20, 30, 40, 50, 60, 90, 120 minutes
  The Sleep Timer can also be activated and deactivated directly with the remote control.

Parental Menu
The Parental Menu offers options to restrict program viewing based on various national rating systems.
To access the menu, enter the 4-digit Password using the keypad on the remote. The factory default password is “0000”.
Adjustment options include:

Program Block
Change Password
Clean All (or reset settings)

Integration and Control

For complete control documentation, please visit www.seura.com/download- center

• RS232 Protocol
• IR Commands

For additional technical support, please contact Séura at 1-800-957-3872 during regular business hours: M-F 8:00 am – 4:30 pm, Central Time.

Troubleshooting

If the product is not working properly, please check the following troubleshooting hints before you contact customer service:

Blank screen

| Check the status LED. If the status LED is red, the Television is in standby and the monitor is black, this is normal. If the status LED is green and the monitor is black, the Television might perform an input scan with no available signal. Please check if an input source is available and that the port of the device has been con- nected correctly in the Service Settings/ Input Ports menu. Press “Menu” on your remote control: you should see the OSD menu. Check your settings for misconfigurations and adjust accordingly. Alternatively, perform

a factory reset to restore the Television to its default settings. If the problem still exists contact customer service.

defects| Check that the signal cable connector is properly connected and that the connection pins are not bent or damaged.
The image is unsatisfactory| Adjust the picture characteristics as described in the above-mentioned section “Video Settings”. Image is not stable Check that the display resolution and frequency from your media source is compatible with the Televi- sion.

Error message: “No Signal”

| Check that the connected media sources are switched on. Check that the signal cable connector is properly connected and that the connection pins are not bent or damaged. Press “Menu” on your remote control: you should see the OSD menu. Check your settings for misconfigurations and adjust accordingly. Alternatively, perform a factory reset to restore the Television to its default settings. If the problem still exists contact customer service.
Low or no sound| Press “Volume Up” and/or “Volume Down” on your remote control and check the audio connection cable(s). Make sure that the Volume Limit setting in the Service Settings menu has been set to an audible value.
Remote control doesn’t work| Press a button on the remote control and check that the status LED of the Television flashes briefly. If it

doesn’t, replace the batteries of the remote control.

Pixel errors

| Pixel errors outside of Séura’s specified and permitted area are covered under Séura’s limited product war- ranty. Please inquire directly with Séura Technical Support regarding Séura’s Pixel Policy.

Ports and Media Support

Input Ports| LINE Audio INPUT| 1 x mini jack and adapter cable: RCA terminal, white, red, yel- low
---|---|---
Component Input| 1 x mini jack and adapter cable: RCA terminal, red, green, blue
HDMI™ Input| 2 x HDMI™ terminal
USB| 1 x USB terminal
RS232| 1 x mini jack and adapter cable: D-SUB 9pin female
IR Input (Infrared)| 1 x mini jack 3.5mm
S-Video| 1 x 4-pin mini DIN
PC Audio In| 1 x mini jack 3.5mm
Output Ports| Speaker Output| 1 x Phoenix clip 4pin
IR Output| 4 x mini jack 3.5mm
Audio Line Out| 2 x mini jack 3.5mm
Video| HDMI™| 480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Component (YPbPr / YCbCr)| 480i, 480p, 576i, 576p, 720p, 1080i, 1080p

Special Features

USB Media Support

Technical Specifications

19 AND 27 INCH CONNECTIONS

1/16″ h
DISPLAY RESOLUTION| 1440 x 900| 1920 x 1080
CONTRAST RATIO| Typical 1000:1| Typical 1200:1
TUNER| ATSC, NTSC, QAM| ATSC, NTSC, QAM
RESPONSE TIME| 3.6ms| 3.5ms
VIEWING ANGLE| 170° Horizontal, 160° Vertical| 170° Horizontal, 160° Vertical
POWER CONSUMPTION| DC 19V 40W / .333A| DC 19V 50W / .417A
INTEGRATION| HDMI| 2| 2
COMPONENT YPBPR, COMPOSITE (AV), VGA| 1, 1, 1| 1, 1, 1
RF COAXIAL ANTENNA| 1| 1
S-VIDEO| 1| 1
USB| 1| 1
RS-232| 1| 1
IR| 1 Input (Mono), 4 Output (Mono)| 1 Input (Mono), 4 Output (Mono)
AUDIO| PC AUDIO IN, VARIABLE| 1, 2| 1, 2
PHOENIX TYPE SPEAKER OUTPUT| 2 x 5W @8Ω/ channel| 2 x 5W @8Ω/ channel
INTERNAL SPEAKERS| None| None
INSTALLATION| PRODUCT DIMENSIONS| 19″ w x 13 1/4″ h x 3 3/16″ d| 28″ w x 17 3/4″ h x 3″ d
ROUGH OPENING SIZE| 18 1/2″ w x 12 7/8″ h| 27 1/8″ w x 16 7/8″ h
COMPATIBLE BACK BOX AND POWER CABLE| BB-19 with 50′ Low-Voltage Power Cable| BB-27 with 50′ Low-Voltage Power Cable
OTHER| CERTIFICATIONS AND COMPLIANCE| FCC, MET

WARRANTY

| Séura’s labor for three (3) years; glass, structure, frame, and assembly for three (3) years; TV including remote and power supply for two (2) years.
REMOTE| Séura IR Remote Control
COMPATIBLE BACK BOX AND POWER CABLE| BB-19| BB-27

Schematic: 19” Model

Schematic: 27” Model

• STEP 1: CUT ROUGH OPENING & INSTALL BACKBOX
• STEP 2: VERIFY TV FUNCTIONALITYSTEP 2: VERIFY TV FUNCTIONALITY
• STEP 3: APPLY SEALANT & INSERT TV ASSEMBLY

LIMITED PRODUCT WARRANTY

For information regarding Séura’s warranty policy, please visit our website: www.seura.com/warranty. If the current Séura warranty policy is after your product purchase date, please contact Séura Customer Support to request warranty documentation from the date of your purchase.
For additional customer support, please contact Séura.
Toll Free: 1-800-957-3872 (Monday – Friday 8:00 am – 4:30 pm, Central Time)
Website: www.seura.com/support

1230 Ontario Road Green Bay, Wisconsin 54311 1-800-957-3872 contacts@seura.com
www.seura.com 

References

• Consumer Product Registration - Séura
• Séura | Technology + Design
• Support - Séura

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>