SECURITY BRANDS 16-X2 Ascent X2 Cellular Multi-Tenant Entry System Installation Guide

16-X2 Ascent X2 Cellular Multi-Tenant Entry System

“`html

Specifications:

• Model: 16-X2
• Power Supply: 12-V AC/DC Adapter
• Components included: Key, Carriage Bolt (4x), Hex Nut (4x),
  Screwdriver

Product Usage Instructions:

Step 1: Unpack and Check Items

Ensure all items are present as shown in the manual.

Step 2: Activation

Complete the activation process before using the unit. Refer to
the Activation Guide included.

Step 3: Mounting

Unlock and open the faceplate for mounting. Use the recommended
gooseneck pedestal and provided hardware. Ensure proper
installation to avoid signal issues.

Step 4: Connecting Wires

Feed wires through the back of the unit and connect as shown
with the included screwdriver. Follow the gate/door opener manual
for accurate connections.

Step 5: Power Supply

When connecting the power supply, match positive to positive and
negative to negative to prevent damage. Use 18-gauge stranded wire
for connections.

FAQ:

Q: What should I do if the unit is not working after

installation?

A: Ensure the activation process is completed as mentioned in
the manual. If issues persist, contact Summit Control for
assistance.

Q: Can I use alternate mounting methods?

A: Alternate mounting is possible, but ensure to purchase and
install the 4G LTE Antenna Extension Kit to maintain signal
strength.

“`

Install GUIDE

1

Unpack box and make sure you have all items shown here.

1 of 2
Model 16-X2

Ascent Unit

12-V AC/DC Adapter

Key

Carriage Bolt
( 4x )

Hex Nut
( 4x )

Screwdriver

r IMPORTANT r
This Ascent unit WILL NOT WORK until the activation process is COMPLETE!
See the included Activation Guide to get this unit activated.
If you need help or have any questions, please contact Summit Control at 972-474-6422.

WARNING
AUTOMATIC GATES CAN CAUSE SERIOUS INJURY OR DEATH!
ALWAYS CHECK THAT THE GATE PATH IS CLEAR BEFORE OPERATING!
REVERSING OR OTHER SAFETY DEVICES SHOULD ALWAYS BE USED!

2

Unlock and open unit faceplate for mounting, wiring, and setup.

r IMPORTANT r
We recommend mounting the unit on a gooseneck pedestal using the included
mounting hardware.
If using alternate mounting, the 4G LTE Antenna Extension Kit
(Model 16-ANTX-1) should be purchased and installed.
Failure to do so may result in NO SIGNAL!

CAUTION

Use all four carriage bolts when mounting the unit to a pedestal.
Leave the “hockey puck” antenna in place even if using an antenna extension.
Seal all openings created in the enclosure.
Failure to follow these instructions can damage the unit!

3

Mount unit to pedestal using included mounting hardware.

(This step may be completed later.)

What’s what?
All important components labeled
Power Terminals For wiring to included power
supply. See Page 2.
Relay Terminals For wiring to gate operator or
door opener. See Page 2. Relay status is indicated by
adjacent LED.
Wiegand Terminals For wiring to Wiegand devices.
See Page 2.
Digital Input Terminals For connecting accessory devices.
Scan QR code on next page for wiring instructions.

Unit shown with faceplate fully open. Internal wiring not shown for clarity.

STOP

This is a cellular accessory for a gate or door. An uninterrupted cellular connection CANNOT BE GUARANTEED!
An emergency egress or primary entry mechanism SHOULD ALWAYS BE USED! (transmitter, fire box, mechanical release)
Consult with your dealer, distributor, and/or system designer for more information.

Cellular Antenna Jacks Jack marked with dashed line is backup jack and not used.
WiFi/Bluetooth Antenna Jack

Power Indicator LED
Directory Insert Fill included insert out by hand to get started right away, or scan the QR code on next page for printable templates.

Call 972-474-6422 Email support@summitcontrol.com
We are available Mon­Fri / 8am­5pm Central

Flip page to continue…

Install GUIDE
4 Connect wires
Feed wires through back of unit, and connect as shown using included screwdriver.

Consult gate/door opener manual for exact connections. Terminals vary widely across manufacturers and models.
Additional wiring diagrams can be found below and online.

2 of 2

Model 16-X2

CAUTION

When connecting the power supply, remember to connect positive to positive and negative to negative to avoid damage.

Reversing polarity can damage the unit and void the warranty!

We recommend using 18-gauge stranded wire for all connections.

Ascent terminals can be unplugged to make wire connections easier.

Relay B can be connected in same manner.

N/C COM N/O N/C COM N/O NEG. (­) POS. (+) POWER (+) POWER (­) COM RADIO FREE EXIT COM COM REVERSE LOOP COM OPEN STOP CLOSE

RELAY B

RELAY A

POWER
12­24 VDC

Ascent Power and Relay Terminals

12-V AC/DC Adapter (included)
The GROUND terminal is optional unless required by local code(s). If using, please connect to earth ground or equivalent.
If plugging into duplex outlet, remove screw from outlet plate, and secure with included screw.

Gate Operator / Door Opener

STOP

Before going forward, double check all wiring and make sure the unit has power!
A wiring diagram for connecting to Wiegand devices can be found below.
For connecting accessories not mentioned, please scan the QR code on this page.
Make sure the gate path is clear before completing Step 5!

5

Key in temporary code 2012 on
keypad and confirm gate opens. If it

does, close and lock unit faceplate.

2012

Adding codes is done in online dashboard and CANNOT be done using keypad on unit!

N
INSTALLATION COMPLETE!
Now follow the Activation Guide to create an account and begin using Ascent.

A Wiegand Device
Feed wires through back of unit, and connect as shown using included screwdriver.
These terminals are used to connect a Wiegand device such as a card reader or Wiegand keypad.
Either set of Wiegand terminals can be used for wiring and then configured in the online dashboard.

CAUTION
Disconnect power to the Ascent unit before connecting Wiegand devices.
Failure to disconnect power can damage the unit!

Need More?
Use the QR code below for printable directory insert templates and more resources, including how-to videos and additional wiring diagrams for connecting accessory devices.

Ascent terminals can be unplugged to make wire connections easier.

DATA 0 DATA 1 GND +12V LED 1 LED 2 DATA 0 DATA 1 GND +12V LED 1 LED 2 LED 1 LED 2 DATA 1 DATA 0 GND +12V

WIEGAND 1

WIEGAND 2

Ascent Wiegand Terminals

© 2024 Security Brands, Inc. All rights reserved.

WIEGAND INPUTS
Wiegand Device

IG-16X2-EN-US Rev. A (7/2024)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>