SECURITY BRANDS 26-100SGL Advantage DKE 100 Code Economy Keypad Installation Guide

June 1, 2024
SECURITY BRANDS

SECURITY BRANDS 26-100SGL Advantage DKE 100 Code Economy Keypad

Product Specifications

  • Model: 26-100SGL
  • Power Source: Electric Strike / Mag Lock
  • Components: Keypad Unit, Gasket, Slotted Screw (2x), Security Screw (2x), L Key, Reset Button, Power Terminals, Relay Terminals

Product Usage Instructions

  • Unpacking and Initial Setup:
    Unpack the box and ensure all components are present as listed in the manual.

  • Mounting the Keypad Unit:
    Prepare a single-gang junction box for mounting the keypad unit.

  • Wiring Instructions:
    Follow the wiring guidelines provided based on your specific setup (Gate Operator, Electric Door Strike, or Mag Lock).

  • Adding Access Codes:
    Enter access codes as required by following the instructions provided in the manual.

  • Testing and Operating:
    Ensure the gate path is clear, enter the access code on the keypad, and verify that the gate opens correctly.

  • Securing the Keypad Unit:
    Secure the keypad unit to the junction box using the provided screws. The gasket is optional for indoor mounting.

Frequently Asked Questions

Q: Can I change the Master Code?

A: Yes, you can change the Master Code by following the instructions provided in the manual under the “Change Master Code” section.

Q: What should I do if I hear a bad tone on the keypad?

A: An incorrect entry will sound a bad tone. Wait for a good tone before proceeding with your input.

What’s what?

Important components labeled

SECURITY-BRANDS-26-100SGL-Advantage-DKE-100-Code-Economy-Keypad-
FIG-3

INSTALLATION

Unpack box and make sure you have everything shown here.

SECURITY-BRANDS-26-100SGL-Advantage-DKE-100-Code-Economy-Keypad-
FIG-1

Prepare existing or install new single-gang junction box to which keypad unit will be mounted after wiring and testing. (Junction box is not included.)

WARNING

  • AUTOMATIC GATES CAN CAUSE SERIOUS INJURY OR DEATH!
  • ALWAYS CHECK THAT THE GATE PATH IS CLEAR BEFORE OPERATING!
  • REVERSING OR OTHER SAFETY DEVICES SHOULD ALWAYS BE USED!

Connect wires.
Wiring for Gate Operator or Door Opener

SECURITY-BRANDS-26-100SGL-Advantage-DKE-100-Code-Economy-Keypad-
FIG-4

Add Access Code(s).
(To add multiple codes, enter each of them before pressing pound key)
Make sure gate path is clear; then enter access code on keypad and confirm gate opens.
Secure keypad unit to junction box using either set of included screws.
(Gasket is optional if mounted indoors.)

SECURITY-BRANDS-26-100SGL-Advantage-DKE-100-Code-Economy-Keypad-
FIG-5

Things to Know

*The Star Key ()**
The star key deletes your current entry.
If you happen to make a mistake keying in a code, simply press the star key to delete the entire entry and start over.

The Pound Key (#)
The pound key is good for one thing and one thing only: exiting Programming Mode. Whenever you’re in Programming Mode, simply press the pound key to get out.

Master Reset Procedure
If for some reason the Master Code and/or Latch Code is forgotten, a reset procedure is available to remedy the situation.
This procedure can be found on Page 4 of this guide.

NOTE: Green arrow indicates “good” tone on keypad. Always wait for good tone before moving on.

INSTALLATION COMPLETE!
Your system is ready to use.

Programming Sub Modes

  1. Add Access Code(s)
  2. Delete Code(s)
  3. Change Master Code
  4. Set Relay Output Time
  5. Set Latch Code
  6. Delete All Codes

Additional Programming

Delete Code(s)
(To delete multiple codes, enter each of them before pressing pound key)

SECURITY-BRANDS-26-100SGL-Advantage-DKE-100-Code-Economy-Keypad-
FIG-6 SECURITY-BRANDS-26
-100SGL-Advantage-DKE-100-Code-Economy-Keypad-FIG-7

Master Reset Procedure

This procedure is used if the Master Code is unknown, or if the Latch Code is unknown and the unit is in Latch Mode. All other codes will be retained after completing this procedure.
NOTE: If an error is made during these procedures, an “error” tone will sound, and you must start again from the beginning.

  • Step 1 – Unscrew mounting screws with L Key and remove keypad unit from junction box.

  • Step 2 – Disconnect power.
    Loosen screw on power terminal block and remove one of two power wires.

  • Step 3 – Press and hold Reset Button; reconnect power; then release Reset Button. Reinsert removed power wire into terminal block and tighten screw to secure. Unit will sound one (1) tone. Release Reset Button after you hear tone.
    The Master Code is now reset to default (1251).

  • Step 4 – Reinstall keypad unit in junction box and fasten mounting screws.

Call 972-474-6422
Email support@summitcontrol.com
We are available Mon–Fri / 8am–5pm Central

© 2024 Security Brands, Inc. All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SECURITY BRANDS User Manuals

Related Manuals