SEURA Artisan Collection Riley Lighted Mirror User Manual
- September 9, 2024
- SEURA
Table of Contents
SEURA Artisan Collection Riley Lighted Mirror
Specifications:
- Product Name: Artisan Collection Riley Lighted Mirror
- Professional installation recommended
- Manufacturer: Seura
- Location: 1230 Ontario Road, Green Bay, WI 54311
- Website: www.seura.com.
Product Usage Instructions
Storing and Removing the Unit:
- Store the unit in a safe place until installation, ensuring it stays protected.
- When removing the unit from the box, lift the mirror by the brackets attached to the back of the mirror glass.
- Do not pull the unit by the frame if the mirror has one, as it may detach.
- Lay the mirror glass flat or upright against a sturdy wall with foam protectors in place.
Installation Precautions:
- Read all instructions and review the drawing package before installation.
- Follow basic safety precautions to reduce the risk of fire, electric shock, or injury.
- Ensure proper wiring with a switched circuit for controlling mirror lights.
Parts and Tools Required:
- Mounting Hardware
- Self-Drilling Drywall Anchors and Screws
- Cables (for hard-wire configuration)
- Level
- Protective Eyewear
- Stud Finder
- Measuring Tape
- Pencil
- Phillips #2 Screwdriver
- Wire Cutter
- Wire Stripper
- Drill
Installation Steps:
- Turn off the main power to the installation location at the circuit breaker.
- Use 3 conductor wires (Black=Live, White=Neutral, Green=Ground) for wiring.
- Ensure the length of the whip is sufficient to reach from the power box to the mirror.
- If needed, use a wire cutter to adjust the length of the whip.
FAQs
Q: What should I do if the mirror or housing has reflective tape?
A: Do not remove the tape as it is not part of the packaging and removing it can damage the product.
Q: How should I handle the mirror during installation?
A: Lift the mirror by the brackets and avoid pulling it by the frame to prevent detachment.
Q: What parts are included in the box?
A: The box typically includes mounting hardware, self-drilling anchors, screws, and the Riley Lighted Mirror.
Q: Where can I find additional product information and manuals?
A: Visit www.seura.com/manuals for product
setup, specifications, warnings, and warranty information.
Thank you for selecting a Séura Lighted Mirror.
Please read this guide before beginning installation.
Carefully remove and inspect the unit for possible damage that occurred during shipping. If there is damage, please call Séura at 1-800-957-3872. If your shipment is damaged and is not noted on the delivery receipt, Séura cannot guarantee compensation. All freight damage claims must be reported to Séura Customer Service within 48 hours of delivery to be covered by our warranty.
How to properly remove the unit from the box
- Carefully lift each item out of the box. Lift the mirror by the brackets attached to the back of the mirror glass. If the mirror has a frame, do not pull the unit out of the box by the frame as the frame may detach from the mirror. Lay the mirror glass flat or upright against a sturdy wall with the foam protectors remaining on the unit.
- If the mirror or mirror housing contains reflective tape or white tape, do not remove it. Adhesive tape is used on some models and is not part of the packaging. Removing the adhesive will damage the product.
How to properly store the unit until installation
- After inspection, repack the unit so it stays safe and protected until installation.
- Séura Lighted Mirrors use LEDs that are rated to retain 70% overall brightness and the end of life, including cases where an individual LED fails.
Safety Instruction
WARNING:
READ ALL INSTRUCTIONS AND REVIEW THE COMPLETE DRAWING PACKAGE BEFORE
ATTEMPTING TO INSTALL OR SERVICE THIS PRODUCT.
When installing and during the use of this product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons including the following:
- Make sure the installation area is free of clutter.
- Do not place the product on an unstable cart, stand, tripod, or table.
- To avoid damage to the mirror, only transport it in a vertical position. Transporting the product horizontally may permanently warp the mirror.
- Inspect the desired location for installation and be aware of all electrical wiring pathways, water pipes, gas lines, or other potentially hazardous conditions that may exist to protect from accidental damage.
- Ensure all required electrical specifications are adhered to have been installed by the appropriate individuals and are code approved.
- Ensure all framing requirements, if needed, have been completed to the building code and pose no structural issues.
- It is highly recommended that at least two (2) people assist in the installation of the mirror.
- Only qualified individuals should attempt to service the product.
- Close adult supervision is necessary when any product is used by or near children.
- Protect against electric shocks and burns by wearing safety gloves.
- Do not operate any product with a damaged cord or plug or operate it after the appliance malfunctions or has been damaged in any manner.
- Do not let the power cord or wiring come in contact with hot surfaces such as radiators, heat registers, stoves, or other products that produce heat.
- To protect against electric shock, do not immerse the power cord, power plug, or product in water or other liquid.
- This product is only intended for use indoors.
- This product is not waterproof. Do not immerse this product in water or expose it to dripping or splashing water as this could cause an electrical hazard.
- In damp locations, it is REQUIRED that the plug-in version of this product is plugged into an electrical outlet protected by a Ground Fault Circuit Interrupter (GFCI) to protect against electric shock, fire, and/or injury. Failure to do so will void any warranty for this product.
- The product must have proper, correct, and sufficient AC supply voltage.
- Retain this manual in a safe place for future reference.
WARNING:
Cancer and Reproductive Harm:
www.p65warnings.ca.gov.
Parts Included
Mounting Hardware
- Self-Drilling Drywall
- Anchors and Screws
(for use when mounting into drywall and not wall studs; quantity varies by mirror size and may include extras)
Parts and Tools
Parts and Tools Required (not included)
Installation
IMPORTANT:
TURN OFF THE MAIN POWER TO THE INSTALLATION LOCATION AT THE CIRCUIT BREAKER.
Step 1: Prepare proper wiring and wall switch.
-
Turn off the main power before installing the fixture to prevent possible electric shock. Locate the circuit breaker control for the room where you’ll be working and switch the circuit to off.
-
A whip is required for hardwire installation. In other words, you need access to a power cable that comes from a Junction Box in the wall. The power cable should be on a switched circuit to allow for control of the mirror lights. These extra wires are pre-wired together. Ensure that you are using 3 conductor wires (Black=Live, White=Neutral, Green=Ground). Make sure the length of the whip is long enough to reach from the power box in the wall to the mirror. If the whip is longer than needed, you may choose to use a wire cutter to reduce the length.
IMPORTANT- Mirrors that include Touch Control functionality require the junction box circuit to be a constant hot circuit and not a switched circuit.
- Mirrors that include a Defogger (non-touch controlled) can be wired in three different ways:
- On the same switch as the mirror lights: When the mirror lights turn on, the defogger turns on. This requires the junction box circuit to be a switched circuit.
- On a separate switch from the mirror lights: One switch will control the mirror lights and a separate switch will control the defogger. This requires the junction box circuit to have separate switched circuits, one for the mirror lights and one for the defogger.
- Always on, no switch required: The defogger will remain on, even when the mirror lights are off. This requires the junction box circuit to be split with one side constant hot (for the defogger) and one side that is switched (for the mirror lights).
-
If your mirror includes dimming capability but does not include the optional Dimmable Touch Button upgrade, verify that your wall switch supports dimming functionality. The dimmable switch must be 0-10V or Triac based on the configuration of your personalized mirror.
Step 2: Map out the installation area and mount the lighted mirror housing to the wall.
- Align the mirror housing on the wall. Using the keyhole at the top center, mark and drill the hole. If mounting on drywall, insert the provided wall anchors using a hammer. This step can be omitted if mounting into studs.
- After securing the mirror housing to the wall with a screw, mark the outermost hole in each corner. Next, remove the mirror housing and drill holes for the provided wall anchors. Install the wall anchors, then rehang the mirror housing and secure it by screwing in all the corners.
Step 3: Make wiring connections.
- Séura lighted mirrors are equipped with an easy-to-install wiring fixture disconnect that can be found on the mirror housing that is now connected to the wall. Refer to your included drawing package to identify the location of the fixture disconnect.
- Connect the whip (extra wires that are pre-wired together) from step 1 to the fixture disconnect. The connection accepts AWG 16 – 12 solid or stranded (19 strands maximum). Using a wire stripper, strip the insulation on the wires back approximately 1/2”.
- Open the fixture disconnect by pushing down on the tab that connects the top and bottom pieces. Connect wires into the fixture disconnect using the color code diagram pictured. Reconnect the top and bottom pieces by sliding them together.
- If using a 0-10V dimmable switch, then connect the 0-10V dimming signal directly to the driver dimming control wires.
- Turn the wall switch on and verify functionality. If on a constant hot circuit, power will be delivered immediately when the circuit breaker is turned back on.
Wiring Fixture Disconnect
Step 4: Hang the mirror
- Hang the mirror onto the housing by positioning the mounting brackets on the back of the mirror so they rest on top of the brackets on the housing. Start by holding the mirror slightly higher than the housing and slowly lower the mirror until the mirror brackets rest on the housing brackets.
- Tuck any extra wire into the wall behind the mirror so it’s no longer visible
- Ensure the brackets are interlocked and the mirror is secure by making sure the mirror is level and evenly spaced from the wall.
Care and Maintenance
Séura’s mirror glass coatings have been developed to protect the mirror surface and allow easy maintenance. Please follow the guidelines listed for proper mirror care and cleaning:
- The glass surface should be cleaned with any conventional non-ammoniated glass cleaner. Do not use any acid, alkali, or ammonia cleaners.
- Care should be taken to use only a soft lint-free cloth. Apply all cleaners directly to the cloth and not the mirror surface. Never saturate the mirror surface as a residual cleaner may seep behind the mirror. Do not allow the mirror edges to remain wet.
- Stubborn spots can be removed with solvents such as mineral spirits, de-natured alcohol, and acetone. Immediately remove solvent and dirt residues per the prescribed methods above with a compatible glass cleaner or water.
- Take care when moving the mirror or accessories near the edges of the mirror. Exposed polished edges of glass are susceptible to chipping when in contact with other hard surfaces such as a faucet or metal soap dispenser.
Decorative frames should be cleaned using a clean, soft cloth to wipe dust and dirt off.