EASTBROOK 40.0028 Wall Mounted Mirror Cabinet Installation Guide
- September 4, 2024
- Eastbrook
Table of Contents
40.0028 Wall Mounted Mirror Cabinet
“`html
Specifications:
- Wall Mounted Mirror Cabinet
- Adjustable stainless steel buffer hinge
- Double layer adjustable tempered glass shelf
- Infrared sensor switch
- Aluminum alloy cabinet
- Double-sided copper-free silver mirror
Product Usage Instructions:
Installation Instructions:
-
Read the instructions carefully before starting the
installation process. -
Turn off the main power switch before beginning
installation. -
Ensure you have the required tools handy: Screw M6, aluminum
alloy bar, tape measure, spirit level, electric drill, screwdriver,
hammer, drill bit, pencil. -
Check the product for any damage before installation to avoid
injury. -
Avoid lifting or installing the mirror cabinet alone due to its
weight. -
Do not use acid or alkaline cleaning agents on the product
surface; use a damp cloth instead.
Installation Steps:
-
Follow the provided installation diagram for proper placement
of the mirror cabinet. -
Adjust the infrared sensor switch and power cord as per the
instructions. -
Check the alignment of the mirror door and adjust using the
hinge screws if needed. -
Ensure the cabinet door is flat against the cabinet by
adjusting the door-cabinet distance screw. -
Loosen the snap screw of the shelf to adjust its position as
required.
FAQ:
Q: Can I install the mirror cabinet alone?
A: It is recommended to have assistance due to the weight of the
mirror cabinet to avoid injury.
Q: Can I clean the mirror cabinet with acid-based
cleaners?
A: No, it is advised not to use acid or alkaline cleaning agents
on the product surface. Please use a damp cloth for cleaning.
“`
Installation Instructions
Packing List
Expansion plug ø8
Required tools
Screw M6
Aluminum alloy bar
Tape measure Spirit level
Electric drill Screwdriver
Hammer
Drill bit
Pencil
Wall Mounted Mirror Cabinet
Adjustable stainless steel buffer hinge
Double layer adjustable tempered glass shelf Infrared sensor switch Aluminum
alloy cabinet
Double-sided copper-free silver mirror
Note: Please carefully read the following before installing
Warning
1. Before installing the product, please carefully read the instructions and
operate accordingly;
2. Before installing, please turn off the main power switch and ensure that
it won’t turn on;
3. The installation of this product requires that the staff has some
electrical knowledge;
4. This mirror cabinet is heavy; do not lift or install with single person in
order to avoid injury;
5. Before installing, please check whether the product is broken, to avoid
injury caused by damaged glass;
6. Do not clean the product surface with acid and alkaline cleaning agent;
please use a damp cloth.
1
2
Installation Steps:
1. Fixing the bar 1.1Open the product packaging, and check whether the
product has any exception or functional damage; if yes, please return it to
the dealer. 1.2 After selecting the location of the mirror cabinet, check
whether the wall is solid, measure the distance of the holes (A, A-1) in the
aluminum alloy bar with a tape measure and mark it on the wall with a pencil
(Fig. 1). 1.3 Drill holes in the marked position with electric drill and ø8
drill bit, and use special ceramic drill if the wall surface is ceramic tile.
1.4 Knock the expansion plugs into the holes in the wall with a hammer, and
then tighten the screws with a screwdriver to fix the bar, and calibrate the
level with a spirit level (Fig. 2).
(A)
(A-1)
Fig.1
2. Positioning and Installation of Mirror Cabinet: 2.1 Attach the mirror cabinet to the bar as shown in Fig. 3, open the cabinet door, and mark on the wall with a pencil (Fig. 4) through the backplane hole (a). 2.2 Remove the mirror cabinet, drill the fixing hole in the wall in the marked position, and place the expansion plugs (Fig. 5). 2.3 Repeat the operation as shown in Fig. 3 and mount the mirror cabinet to the bar, make sure that the circuit on the wall is not energized and connect the three-core wire reserved on the wall to the three-core wire terminal block on the product (Fig. 6), and then tighten the screws on the backplane. 2.4 Finally, turn on the main switch, and test if the switch works normally (Fig. 7).
Fig.3
a Fig.4
Fig.2 3
Fig.5
1
Product power cord Reserved power cord Fig.6
4
Infrared sensor switch Fig.7
5
Distance 50mm (max.)
3. Mirror Door Adjustment 3.1 Fix the mirror cabinet, and check if the mirror
door is flat; if not (as shown in Fig. 8), adjust the distance of the door
opening by adjusting the hinge screw (b) and keep the door level (Fig. 9).
Fig.8
b
Rotate CW: Door moves to the center of the mirror cabinet Rotate CCW: Door
moves to both sides of the mirror cabinet
Fig.9 6
3.3 If the cabinet door isn’t flat (Fig. 10), adjust the distance between the
door and the cabinet by adjusting the screw (c) to make the door flat.
(Fig.11)
Warning: The distance between the door and the cabinet should not be too
small, otherwise the door can’t be opened and may lead to the door rupture.
Fig.10
c
4. Loosen the snap screw (d) of the shelf to adjust the shelf position. (Fig.12)
Rotate CW: Distance between door and cabinet reduces Rotate CCW: Distance
between door and cabinet increases
Fig.11
7
d Safety Warning
Fig.12
Do not disassemble the door unless necessary
8
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>