Eastbrook 36.0067 90cm Left Hand Door Corner Cabinet Basin Unit Instruction Manual

Eastbrook 36.0067 90cm Left-Hand Door Corner Cabinet Basin Unit

Specifications:

• Product Name : Bathroom Furniture
• Types : Floorstanding Vanity Units, Wall Hung Vanity Units
• Manufacturer Contact : Eastbrook Road, Gloucester GL4 3DB
• Technical Helpline: 01452 317890 (Mon – Fri 8:00am-17:00pm)

Product Usage Instructions

Installation for Floorstanding Vanity Units:

1. Mark two holes levelly on the wall.
2. Drill the holes using a proper size drill bit.
3. Insert expansion wall plug or appropriate alternative wall fixing.
4. Screw in the tapping screws and add cover caps on the screws.
5. Apply adequate silicone between the basin and unit to prevent water ingress.

Installation for Wall Hung Vanity Units
Follow the provided diagram for screw hole locations and wall clip installation.

1. Mark the holes levelly on the wall.
2. Drill the holes using a proper size drill bit.
3. Insert expansion wall plug or appropriate alternative wall fixing.
4. Screw in the tapping screws.
5. Apply adequate silicone between the basin and unit to prevent water ingress.

Components Adjustment:

• Drawer Slider Adjustment: Turn the screw clockwise to raise the drawer, anti-clockwise to lower it.
• Soft Closing Hinge Adjustment: Adjust up/down, in/out, left/right as needed for proper operation.
• Wall Hanging Bracket Adjustment: Turn the screw anti-clockwise to lengthen the hook’s protrusion.

Aftercare and Maintenance:

• Ensure proper ventilation in your bathroom.
• Avoid abrasive cleaning materials and acidic substances for cleaning.
• Clean with agents having a PH of 7.
• Keep the vanity unit dry and free from continuous moisture.
• Wipe off spillages and splashes promptly.
• Regularly check hinges and sliders every 6 months for any loose screws.

PLEASE READ BELOW NOTES BEFORE INSTALLING YOUR VANITY UNITS.

• Use protective gloves and eye protection at all times
• Please use qualified plumbers to install the vanity unit
• 2 people are required to install the units
• Check the parts are fully supplied
• Never install products or components which looks damaged
• Hinges for doors and sliders for drawers may need to be checked and adjusted to achieve proper position after installation
• Please avoid direct sunlight as this will affect the painted surface colour change
• If fixing to a stud or panelled wall, proper framework is required to support a wall hung unit

NECESSARY TOOLS (not supplied)

Installation for Floorstanding Vanity Units

• Mark the two holes levelly on the wall.
• Drill the holes using proper size drill bit.
• Insert expansion wall plug or appropiate alternative wall fixing.
• Screw in the tapping screws.
• Add cover caps on the screws.

When fitting the basin to the unit, adequate silicone is required between basin and unit to prevent potential water ingress.

Installation for Wall Hung Vanity Units

Mark the holes levelly on the wall. Drill the holes using proper size drill bit. Insert expansion wall plug or appropiate alternative wall fixing. Screw in the tapping screws.

When fitting the basin to the unit, adequate silicone is required between basin and unit to prevent potential water ingress.

Components Adjustment

Drawer slider adjustment
If you need some fine adjustment, turn the screw clockwise to to get the drawer “up”, turn the screw anti-clockwise to get the drawer “down”

Soft closing hinge adjustment

Wall hanging bracket adjustment

Aftercare and Maintenance

• Make sure your bathroom is well ventilated
• Do not use abrasive cleaning materials which will hurt the surface finish
• Do not use any cleaning with acidic substances or soda. We suggest use cleaning agents with a PH of 7
• The vanity unit must be kept dry and not subject to continuous moisture
• All spillages and splashes must be wiped off
• Do not lean on fully opened doors or drawers
• Check the hinges and sliders every 6 months and any loose screws must be tightened

Technical Helpline : 01452 317890 (Open times: Mon – Fri 8:00am-17:pm)

Email: technical@eastbrookco.com

Eastbrook Road, Gloucester GL4 3DB

FAQ

Q: Can I install the vanity unit by myself?
A: It is recommended to use qualified plumbers and have two people for installation to ensure safety and proper setup.

Q: How often should I check the hinges and sliders?
A: It is advised to check the hinges and sliders every 6 months and tighten any loose screws as needed to maintain functionality.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>