FRONT RUNNER SSBS009 Load Bed Cargo Slide Installation Guide
- September 3, 2024
- Front Runner
Table of Contents
SSBS009 Load Bed Cargo Slide
“`html
Product Information
Specifications:
- Product Name: Load Bed Cargo Slide MKIII – LARGE
- Model: SSBS009
- Size: Large
Product Usage Instructions
1. Get Organized
Before starting the installation, familiarize yourself with the
components received:
- 1x Load Bed Cargo Slide MKIII – LARGE
- 1x M6x25 Countersink Bolt
- 1x M10 Flat Washer
- 1x M6x40 Hex Bolt
- 9x M8 Nyloc Nut
2. Fit and Secure
2.1 Removing Wood Base
Before fitting the Cargo Slide, remove the wood base by
loosening the four M6 Button Head Bolts.
2.2 Loosening Rubber Stopper
Remove the rubber stoppers from both rear corners of the Cargo
Slide by gripping and unscrewing the M6 button head bolts.
2.3 Placing Cargo Slide
Carefully place the Cargo Slide into the vehicle’s load bed.
Position the frame properly, ensuring it aligns correctly with the
mounting points.
2.4 Marking and Drilling Holes
Mark the mounting points on the load body, drill 4mm pilot
holes, and then re-drill them to 9mm. Insert M6 rivnuts into each
hole.
2.5 Securing the Frame
Place the frame back onto the load bed, use spacers if needed,
and secure it using the provided fasteners.
Frequently Asked Questions (FAQ)
Q: What should I do if the mounting points do not align with
raised sections in my load bed?
A: Spacers have been provided to accommodate situations where
mounting points do not align with raised sections. Use the spacers
over the rivnuts when mounting points are in a dip.
“`
Load Bed Cargo Slide MKIII – LARGE
ENG
SSBS009
READ ME ! Thank you for pRurEchAasDingMa FEron!t Runner Load Bed Cargo Slide.
Before you start, take a moment to familiarize yourself with the Fitting
Instructions and the components received. Refer to Page 2 for a list of all
the components, quantities and tools required.
NOTE: Front Runner will not be responsible for any damage caused by the
failure to install the product according to these instructions. Please call us
if you have any questions about the installation of this product.
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY
ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN
AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE
RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR
VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING
THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE YOU MUST READ AND
UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT
RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF
THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE
NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE
PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
SSBS009_REV_A02
1
© COPYRIGHT 2018 FRONT RUNNER VEHICLE OUTFITTERS
1 GET ORGANIZED
Here is what you are looking at for SSBS009
IN THE BOX
1 1X 2 1X 3 1X 4 9X 5 2X 6 5X 7 10 X 8 9X 9 6X 10 9 X 11 1 X 12 1 X 13 1 X 14 1 X
Load Bed Cargo Slide MKIII – LARGE M6x25 Countersink Bolt M10 Flat Washer M6x40 Hex Bolt M8 Nyloc Nut M6x25 Hex Bolt M6 Rivnut M6 Spring Washer 19×12.58×12 Aluminium Spacer M6x30x1 Flat Washer M6x35 Hex Bolt M6x40 Hex Bolt M6 Normal nut M6x12x1 Flat Washer
FIGURE 1.1
TOOLS NEEDED
10MM 17MM
10MM 17MM
4mm 9.5mm
4mm
2 4 6 8
17 10
12
11
14
SSBS009_REV_A02
1 3 5 7 9 11 13
© COPYRIGHT 2018 FRONT RUNNER VEHICLE OUTFITTERS
2 FIT AND SECURE
2.1
10MM
Before fitting the Cargo Slide in the vehicle, remove the wood base by
loosening the four M6 Button Head Bolts.
To loosen the two rear bolts, open the Cargo Slide.
2.2 2.3
SSBS009_REV_A02
Stopper
Looking at both the left and right rear
corners of the Cargo Slide (Item 1), loosen
and remove the rubber stopper. This is done
by gripping the stopper to prevent it from t
urning and removing the M6 button head
4MM
bolt as shown. Once removed keep in a safe place as you will need to replace them at a
later stage.
Place the Cargo Slide into the vehicles load bed. Carefully pull the “tray” free from the frame and store in a safe place until later.
17MM 17MM
Position the frame, front to back and left to right. Load beds vary with each
manufacturer, so the exact positioning of the frame will vary from vehicle to
vehicle. I t is advisable to get all mounting points in the center of the
raised sections that run the length of the load bed, however in the event of
mounting points not lining up with raised sections,spacers have been provided.
The front mounting brackets may be relocated backwards should it be required
to obtain a more suitable mounting position as shown in diagram 2.3.
3
© COPYRIGHT 2018 FRONT RUNNER VEHICLE OUTFITTERS
2 FIT AND SECURE
2.4
Make sure you have closed the load bed tail gate to ensure that it does not make contact with the frame. Once you are satisfied with the positioning of the frame, mark the position of all the mounting points as indicated by the arrows onto the load body.
Remove the frame and drill a 4mm pilot
4MM 9MM
hole on each of your markings. Check the underside of the load bed before drilling to
make sure that there is no piping or wiring
in the way. Re-drill all of the pilot holes to
9mm.
Insert and crimp a M6 rivnut (Item 6) into each of the holes you have drilled.
2.5
Place the frame back onto the load bed and
secure using the fasteners and spacers
supplied. The spacers (Item 5) are to be
used when the mounting points are in a
4MM
“dip” and not on a raised section by
placing it over the rivnut so that the frame
rests on the spacer.
10MM
When securing the front of the frame use the M6x25 countersunk screw, M10 flat
washer and a spacer
10MM
2.6
11
10MM
Before refitting the slide to the frame, use the M6 x 35 or M6 x 40 hex bolt
(Item 11 or 12) (depending on which fits the specific vehicle best) together
with the M6 Normal
nut and M6 x 12 x 1 Flat washer (Item 13 &
14) and assemble as shown.
12 13
Turn the Bolt until the bottom of the bolt touches the load bin then tighten the M6 normal nut to lock the M6 bolt in place.
The above adjustment can be repeated
14
as needed.
Tightening Torque: M6 : 8-10Nm / 5.9 ft lb – 7.38 ft lb
SSBS009_REV_A02
4
© COPYRIGHT 2018 FRONT RUNNER VEHICLE OUTFITTERS
2 FIT AND SECURE
2.7
3 COMPLETION
3.1
Refer to Step 2.2, refit the tray and stoppers. Once refitted check that the
push to close latch engages fully and that the slide is secure.
If the Lock dose not Lock properly adjust the bolt inserted in 2.6.
Congratulations! You did it. Take a step back and admire your work!
4 INSTALL OTHER VEHICLE AND RACK ACCESSORIES
Now’s the time to visit your favorite Front Runner Dealer in person or online.
SSBS009_REV_A02
5
© COPYRIGHT 2018 FRONT RUNNER VEHICLE OUTFITTERS
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>