VOLLRATH R39737 One Piece Cafeteria Breath Guard Installation Guide

: June 1, 2024
: VOLLRATH

Table of Contents

VOLLRATH R39737 One Piece Cafeteria Breath Guard
Product Information
Product Usage Instructions
FAQs
INSTALLTION INSTRUCTION
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VOLLRATH R39737 One Piece Cafeteria Breath Guard

Product Information

Specifications:
- Product Name: Cafeteria Breath Guard
- Model: One Piece and Three Piece
- Manufacturer: Vollrath Company, L.L.C.
- Item No.: 2350030-01

Product Usage Instructions

One Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figure 1. Repeat for all four uprights.
Three-Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.

FAQs

Q: What should I do if I encounter cracked plastic while tightening the cap nuts?
- A: If you notice cracked plastic, stop tightening immediately to prevent further damage. Contact Vollrath’s service department for assistance.
Q: Can I disassemble the breath guard for cleaning purposes?
- A: Yes, you can disassemble the breath guard following the installation steps in reverse. Make sure to clean each component thoroughly before reassembling.

INSTALLTION INSTRUCTION

These instructions cover the installation of the one-piece Cafeteria Breath Guard and the three-piece Cafeteria Breath Guard.

One Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:
NOTE: Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
- Figure 1. One Piece Breath Guard Installation
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
Install the one-piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
Install the side breath protector (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.

Three-Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:
NOTE: Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
- Figure 2. Three-Piece Breath Guard Installation
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
Install the side shield (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.