25 Inch Pro Multi Floor Cutter
Owner’s Manual 9-volt battery sold separately

10-959 25 Inch Pro Multi Floor Cutter

WARNING Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious bodily injury. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

|
---|---
https://www.qep.com/qr/?go=Roberts-Precision- Cuts_Video| https://www.qep.com/qr/?go=10-959_25in_Floor_Cutter
| WARNING
---|---
VERY SHARP BLADE

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY! USING THIS MACHINE WITH RESPECT AND CAUTION WILL CONSIDERABLY LESSEN THE POSSIBILITY OF PERSONAL INJURY.

SAFETY RULES FOR THE PRECISION CUTS™ MULTI-FLOOR CUTTER

1. READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE OPERATING THE PRO MULTI-FLOORING CUTTERS.
2. If you are not thoroughly familiar with the operation of Precision Cuts ™ Pro Multi-Floor Cutter, obtain advice from a qualified instructor.
3. Stay alert. Do not operate while under the influence of drugs, alcohol, or medication.
4. Always wear safety approved eye protection with side shields (ANSI Z87.1)
5. Keep work area free of debris.
6. Keep children and unauthorized persons away from the Precision Cuts™ Pro Multi-Floor Cutter and work area.
7. Make sure tool is secure. Operate only on a firm substrate or solid stand.
8. Use the right tool. Do not force the Precision Cuts™ Pro Multi-Floor Cutter or use it for a job which it is not designed for; use only on approved materials.
9. Keep the blade sharp. A dull blade will not perform properly.
10. Always keep hands away from blade while operating or carrying the cutter.
11. Do not alter or misuse this tool. The Precision Cuts™ Pro Multi-Floor Cutter is precision built; modifications not specified in this manual may result in a dangerous and unsafe environment.
12. Maintain the Precision Cuts™ Pro Multi-Floor Cutter with care. Keep Blade sharp and clean. Follow instructions for changing accessories.
13. Use only recommended accessories. The use of improper accessories may be hazardous and cause injuries.
14. Never leave Precision Cuts™ Pro Multi-Floor Cutter to be unattended Secure the handle with the locking device when not in use.

SET UP

Installation Install the wheel assembly to the cutter base with provided bolts and nuts as shown.
Then insert the handle into the handle base as show and tighten provided screw.
Warning: Do not put your fingers against the sharp edge of the blade at any time.

CUTTING

45° Cut
Adjust the angle attachment to 45°. Insert material between the cutting blade and the base, against the angle attachment as shown, then press the handle down to complete a cut.
Warning: Maintain control of the handle. Do not allow handle to slam back after making a cut.

MAINTENANCE

Changing the Blade
Use the provided Allen wrench to remove the nine screws, then hold the blade by each end and carefully move the blade out of blade holder.
Note: the flat side of the blade should face the working table when installing a new blade.
Warning: Do not put your fingers against the sharp edge of the blade at any time. Changing the Nylon Bar
Use the provided Allen wrench to remove the ten screws, then hold the nylon bar and carefully move it out of nylon bar holder.
Warning: Do not put your fingers against the sharp edge of the blade at any time. Transport
Lock the handle in the down position by sliding the locking pin on the eccentric cam as shown.
Carry the cutter using the table opening as shown

ROBERTS 10-959 PARTS DIAGRAM

ROBERTS 10-959 PARTS LIST

| Parts|

Qty

---|---|---
1| Screw M5X12| 2
2| Washer OI 6| 2
3| Rubber Feet A| 2
4| Screw M8X52| 4
5| Screw M8X55| 14
6| Left Wheel Base| 2
7| Cutter Base| 1
8| Screw M4X14| 10
9| Screw M8X40| 2
10| Blade| 1
11| Washer 10| 4
12| Carry Wheel| 2
13| Nylon Bar| 2
14| Right Wheel Base| 2
15| Spring| 2
16| Rod| 2
17| Screw M8X16| 2
18| Screw M5X10| 9
19| Stopper| 1
20| Blade Holder| 1
21| Nut M12| 1
22| Aluminum Eccentric Cam| 1
23| Shaft| 2
24| Aluminum Wheel| 2
25| Nylon Wheel| 2
26| Screw M8X12| 3
27| Handle Base| 1
28| Screw| 1
29| Latch| 1
30| Bolt M12X120| 1
31| M8 Screw B| 2
32| Handle A| 1
33| Handle Base| 1
34| M8 Screw A| 1
35| Nut M4| 2
36| Right ABS Handle| 1
37| Guide Bar| 1
38| Left ABS Handle| 1
39| Screw M4X30| 2
40| Working Table| 1
41| End Board| 1
42| Screw M8X16| 6
43| Screw M5X20| 4
44| Locker Nut M5| 4
45| Rubber feet B| 2
46| Cross Bar| 2
47| Left Side Frame| 1
48| Battery Box / Light Belt Assembly| 1
49| Working Table Sporting| 2
50| Locker Nut M8| 12
51| Left Side Frame| 1

CUTTING CAPACITY CHART

WOOD FLOORING| JANKA HARDNESS RATING|

WILL CUT UP TO
5/8″ ENGINEERED
WOOD FLOORING

---|---|---
Eastern White Pine| 380| Yes
Basswood| 410| Yes
White Pine| 420| Yes
Hemlock| 500| Yes
Chestnut| 540| Yes
Larch| 590| Yes
Douglas Fir| 660| Yes
Southern Yellow Pine (Loblolly and Shortleaf)| 690| Yes
Shedua| 710| Yes
Sycamore| 770| Yes
Parana| 780| Yes
Lacewood / Leopardwood| 840| Yes
Southern Yellow Pine (Longleaf)| 870| Yes
Cedar| 900| Yes
Paper Birch| 910| Yes
Boire| 940| Yes
Black Cherry / Imbuia| 950| Yes
Sakura| 995| Yes
Teak| 1000| Yes
Black Walnut| 1010| Yes
Boreal| 1023| Yes
Makore| 1100| Yes
Brazilian Eucalyptus / Rose Gum| 1125| Yes
Cocobolo| 1136| Yes
Carbonized Bamboo (represents one species)| 1180| Yes
Heart Pine| 1225| No
Movingui| 1230| No
Yellow Birch| 1260| No
Carribean Heart Pine| 1280| No
Red Oak (Northern)| 1290| No
American Beech| 1300| No
Ash (White)| 1320| No
Ribbon Gum| 1349| No
Tasmanian Oak| 1350| No
White Oak| 1360| No
Australian Cypress| 1375| No
Natural Bamboo (represents one species)| 1380| No
Coffee Bean| 1390| No
Hard Maple / Sugar Maple| 1450| No
Sweet Birch| 1470| No
Curupixa| 1490| No
Kambala| 1540| No
Peroba| 1557| No
True Pine / Timborana| 1570| No
Zebrawood| 1575| No
Tualang| 1624| No
Wenge / Red Pine| 1630| No
Highland Beech| 1686| No
Locust| 1700| No
Kempas| 1710| No
Merbau| 1712| No
Blackwood| 1720| No
African Padauk| 1725| No
Rosewood| 1780| No
Bangkirai| 1798| No
Afzelia / Doussie| 1810| No
Hickory / Pecan / Satinwood| 1820| No
Goncalo Alves / Tigerwood| 1850| No
Purpleheart| 1860| No
Jarrah| 1910| No
Amendoim| 1912| No
Merbau| 1925| No
Tallowwood| 1933| No
Cameron| 1940| No
Bubinga| 1980| No
Sydney Blue Gum| 2023| No
Karri| 2030| No
Brushbox| 2135| No
Pradoo| 2170| No
Santos Mahogany / Bocote / Cabreuva| 2200| No
Mesquite| 2345| No
Brazilian Cherry / Jatoba| 2350| No
Spotted Gum| 2473| No
Red Mahogany / Turpentine| 2697| No
Bloodwood| 2900| No
Angelim Pedra| 3040| No
Brazilian Redwood / Paraju| 3190| No
Ebony| 3220| No
Cumaru / Brazilian Teak| 3540| No
Ipe / Brazilian Walnut / Lapacho| 3684| No

STRICTLY FOLLOW THIS CUTTING CAPACITY CHART. ANY ATTEMPT TO CUT FLOORING HARDER THAN WHAT IS LISTED MAY CAUSE PERSONAL INJURY AS WELL AS DAMAGE TO THE PRODUCT.

robertsconsolidated.com
Roberts Consolidated Industries, Inc.
Boca Raton, FL 33487
Made in China • Fabriqué en Chine
Hecho en China • F1924-12270
CUSTOMER SERVICE: 1-866-435-8665

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>