ESX VN1040-4G Smart Naviceiver Installation Guide

V1.5
TION ALLA GUIDE
INST

SMART NAVICEIVER MOBILE INTERNET READY VISION ANDROID™ SERIES

IMPORTANT NOTES

This guide is an aid for the professional installation of the device. Please note the following notes before installation:

• Always handle all parts of the device and the components of your vehicle with care.
• Under all circumstances observe the regulations of the vehicle manufacturer and do not make any changes to the vehicle which could impair driving safety.
• For safety reasons, disconnect the vehicle battery’s ground connection before installation.
• Please always pay attention to the correct polarity of the connections.
• Please do not modify any harnesses or connections of the device or the vehicle as this may affect the warranty.
• Make sure that no cables are squashed or cause a short circuit.
• Do not lay cables in front of the airbags, e.g. in the dashboard or in a way that affects their function.
  NOTE:
  For many vehicle models, a vehicle-specific 1-DIN installation set is required for professional installation. In order to be able to use the existing steering wheel remote control of your vehicle, a vehicle-specific adapter may also be required. You can obtain information about this on the Internet or from your specialist dealer.

INSTALLATION HINTS

Please note the following steps when installing the device:

1. Original radio/navigation system
   If available, first remove the original radio/navigation device. Use suitable unlocking tools to pull the device out of the dashboard. Then pull the cable plug from the device
   and leave it accessible in the radio slot.

2. Cabling of the ESX main device
   Lay the supplied cable sets and antennas in the vehicle. Please note the information on the next page. Then connect all cable sets, antennas, and dongles to the ESX main
   device as described on page 6. Then plug in the cable plug from the radio slot of the vehicle on the ESX main unit or on its vehicle-specific system cable set.

3. Installation of the ESX main device
   Now the ESX main device can be inserted into the 1-DIN installation slot of the vehicle.

4. Functional test
   Before you complete the installation, you should perform a function test. Check all functions of the ESX naviceiver including the steering wheel remote control of the
   vehicle.

RECOMMENDED TOOLS

SCOPE OF DELIVERY

AV cable set 1 with audio and video
connections incl. rearview camera
(14-pin connector)| 1
USB port 1 (4-pin connector)| 1
4G/LTE dongle (6-pin connector)| 1
USB port 2 (8-pin connector)| 1
Camera cable set for HD rearview camera
(10-pin connector)| 1
AV cable set 2 with power, audio and video
connections, additional camera input (8-pin connector)| | 1
---|---|---
External microphone (6-pin connector)| 1
GPS antenna| 1
DAB antenna| 1
4G/LTE antenna| 1
VNA-LFB-FD6 Adapter for analog steering wheel remote control (Only VNC1040 -DBJ-4G and VNC1045-DBJ-4G)| 1

WIRING DIAGRAM

Assignment system socket

S System cable set 1 (20-pin connector, black)

(right)
Cable brown (CAN-RXD):| Currently not used
Cable orange (AMP CON)*:| Remote turn-on signal for external amplifiers (+12V)
Cable black (GND):| Ground connection for devices such as cameras

*must be activated in the Naviceiver in the app “DSP” under “EXT AMP”

NOTE:
The handbrake signal must be connected to BRAKE. When the handbrake is applied, the signal must be connected to the ground. According to legal regulations, the device may only play videos on the main screen when the handbrake is engaged. The connection cable must therefore not be permanently connected to the ground. While driving, the screen is switched off to avoid accidents caused by carelessness.

Assignment of AV connections

A AV cable set 1 (14-pin connector, black)

G AV cable set 2 (8-pin connector, blue)

E Camera cable set for HD rearview cam (10-pin connector, yellow)

RCA yellow (AHD-CAM):| Video input for the high-resolution rearview camera (Only for compatible HD cameras)
---|---

GENERAL INSTALLATION INSTRUCTIONS

GPS antenna
The GPS antenna must be glued horizontally to the front of the dashboard. No reception is possible if the window is metalized. Choose a flat spot with a clear view of the sky. The location must be about 50 cm away from the main unit, otherwise, the GPS measurement accuracy will be reduced. When installing the GPS antenna in the vehicle, the GPS accuracy is determined by the installation position and body shape of the vehicle. The accuracy is usually lower when the GPS antenna is installed in the vehicle. Remove the film on the underside of the GPS antenna

DAB antenna
Route the DAB antenna to the windshield and attach it there.

Clean the windshield with a suitable
cleaning cloth.
NOTE:
In newer vehicles, the original vehicle antenna can usually be used for both analog and digital radio reception. The enclosed DAB window antenna should only be used if a fender or roof antenna is available.

Remove the carrier sheet of the black amplifier unit and the foil antenna and stick the antenna to the window. ontscheibe it inter). usually The no Glue the copper-colored metal surface of the grounding sheet to a bare metal part of the vehicle.

External microphone
The external microphone should be positioned in an easily accessible location, e.g. next to the sun visor or on the steering column.
USB ports
Route the USB ports to the desired location, e.g. to the glove compartment.

SETUP THE 4G/LTE INTERNET CONNECTION

1. First lay the two 4G/LTE antennas inside the dashboard towards the windshield, one antenna for the left and one for the right.
2. Ideally, you should stick the antennas to the windshield to ensure optimal reception.
3. Then insert your SIM card in the 4G/LTE dongle:

Open the dongle by pushing the flap to the right.| Now open the metal flap carefully with a suitable tool
by pushing the flap up.

Then insert your SIM card with the contacts facing down.| Close and lock the metal flap carefully by pushing the flap down.

Compatible SIM cards:

Micro SIM
Nano SIM with adapter for Micro SIM

SETUP THE 4G/LTE INTERNET CONNECTION

4. Then turn on the device to test the 4G/LTE connection.

After the device has started, enter your 4-digit PIN code of the SIM card
here. Confirm the entry with the tick.| After successful entry, the SIM card is unlocked.

If the device is successfully connected to the mobile Internet, the
The „LTE“  symbol appears in the status bar at the top right.| If the device is turned off, you have to enter the PIN code of the SIM card
again after each restart, just like with a smartphone*.

5. After a successful test, install the 4G/LTE dongle in the radio slot or dashboard.

• The SIM card‘s PIN query can be deactivated in standard smartphones. To do this, insert the SIM card in a smartphone and deactivate it accordingly. The steps involved
  vary depending on the smartphone.

ESX Car Media Systems · Audio Design GmbH
Am Breilingsweg 3 · D-76709 Kronau/Germany
Tel. +49 7253 – 9465-0 · Fax +49 7253 – 946510
www.esxnavi.de – www.audiodesign.de
© All rights reserved. Subject to technical changes and errors.

References

• Audio Design - The Home Of Car Audio, Navigation And More ...
• ESX - Car Media Systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>