ATEN VM7904 4 Port 4K DisplayPort Input Board User Guide

: August 31, 2024
: Aten

Table of Contents

VM7904 4 Port 4K DisplayPort Input Board
Product Information
Specifications
Product Usage Instructions
Hardware Setup
Source and Display Device Installation
- FAQ
Q: Is the VM7904 hot-swappable?
Q: Where can I find support and documentation for ATEN
Q: What are the compliance standards for the VM7904?

VM7904 4 Port 4K DisplayPort Input Board

Product Information

Specifications

Model: VM7904
Ports: 4 DisplayPort Input Ports
Resolution: 4K
Compatibility: ATEN 16 x 16 Modular Matrix Switch and other
compatible Modular Matrix Switches

Product Usage Instructions

Hardware Setup

Power off the Modular Matrix Switch.
Unscrew the two Phillips head screws on the rear of the Modular
Matrix Switch and remove the back panel cover.
Slide the VM7904 into any of the Input Board Slots (4 upper
slots) on the Modular Matrix Switch until it secures in place.
Tighten the screws on the VM7904 to fasten it to the Modular
Matrix Switch.
To install more I/O boards, repeat steps 2 to 4.

Source and Display Device Installation

Connect your A/V source device to the DisplayPort and audio
input ports of the VM7904.
Power on the Modular Matrix Switch and all devices in the
installation.

FAQ

Q: Is the VM7904 hot-swappable?

A: Yes, the VM7904 is hot-swappable, allowing for easy
installation and replacement without powering down the system.

Q: Where can I find support and documentation for ATEN

products?

A: You can find technical support, documentation, firmware,
software utilities, and specifications online at ATEN’s official
website: http://www.aten.com/download/

Q: What are the compliance standards for the VM7904?

A: The device complies with Part 15 of the FCC Rules, ensuring
it meets regulatory standards for electromagnetic interference.

VM7904
4-Port 4K DisplayPort Input Board Quick Start Guide
Package Contents 1 VM7904 4-Port 4K DisplayPort Input Board 4 Terminal Blocks 1 User Instructions

VM7904 Front View

1

2

3

Hardware Review
VM7904 Front View
1. DisplayPort Input Ports 2. Audio Input Ports 3. Status LED

Hardware Setup
I/O Board Installation
An ATEN 16 x 16 Modular Matrix Switch is used as an example in the instructions below. For a list of compatible Modular Matrix Switches, please visit our official website. 1. Power off the Modular Matrix Switch.
Note: The VM7904 is hot-swappable. 2. On the rear of the Modular Matrix Switch, unscrew the two Phillips
head screws and remove a back panel cover.

3. Slide the VM7904 into any of the Input Board Slots (4 upper slots) on the Modular Matrix Switch until it secures in place.

4. Tighten the screws on the VM7904 to fasten it to the Modular Matrix Switch.
5. To install more I/O boards, repeat steps 2 to 4. 6. Proceed to the next section to install a source device.

Source and Display Device Installation 1. Connect your A/V source device to the DisplayPort and audio input ports of the VM7904. 2. Power on the Modular Matrix Switch and all devices in the installation.
1

2

Support and Documentation Notice
All information, documentation, firmware, software utilities, and specifications contained in this package are subject to change without prior notification by the manufacturer. To reduce the environmental impact of our products, ATEN documentation and software can be found online at http://www.aten.com/ download/
Technical Support www.aten.com/support

Scan for more information
EMC Information FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Warning: Operation of this equipment in a residential environment could cause radio interference.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
(A) , .
© Copyright 2018 ATEN® International Co., Ltd. ATEN and the ATEN logo are trademarks of ATEN International Co., Ltd. All rights reserved. All other trademarks are the property of their respective owners. This product is RoHS compliant.