Motherwell Products MWL-667 Indian Luggage Rack for Backrests Installation Guide

August 31, 2024
Motherwell Products

Motherwell Products MWL-667 Indian Luggage Rack for Backrests

Motherwell-Products-MWL-667-Indian-Luggage-Rack-for-Backrests-
PRO

Product Information

Specifications:

  • Fitment: Fits on 691S and 691T (Indian Chieftain, Springfield, Roadmaster, & Challenger)
  • Max Capacity: 10 lbs
  • Material: 3/4 Tubular Steel, 12-gauge CR Steel
  • Technical Specs: Fits MWL-691s & MWL-691T (MB/GB/CH)

Product Usage Instructions

Tools Required: 7/16 Wrench or 11 pt. Wrench Kit 23 (included)

Mounting Procedure:

  1. Remove backrest from the bike if installed.
  2. Remove 4 existing bolts on the inside of the Sissybar side plates on Rack mounting block.
  3. Slide luggage rack from inside bottom backrest to align with existing bolt holes.
  4. Insert the 4 bolts provided and tighten until just snug, check rack is square, and adjust as needed, then tighten bolts fully.
  5. Reinstall bar on bike.

Use and Care:
Wash your accessories with the same care you use when washing your motorcycle. Use mild soap and water. DO NOT use abrasive chemicals or cleaners. We recommend the use of non-abrasive automobile wax to polish our products. This will best maintain the appearance of the product and increase longevity.

Warnings:
Never carry more than 10 lbs. on rack, and always secure cargo properly. Failure to do so can affect handling. Make sure neither cargo straps are loose and come in contact with moving parts, i.e., wheels, brakes, etc…

FAQ:

  • Q: Can I exceed the maximum capacity of 10 lbs on the luggage rack?
    A: No, it is important to never carry more than 10 lbs on the rack to ensure safe handling.

  • Q: How should I clean the luggage rack?
    A: Wash the rack with mild soap and water. Do not use abrasive chemicals or cleaners. To maintain the appearance, polish with non-abrasive automobile wax.

PRODUCT INSTRUCTION

WELCOME: These instructions describe the procedure for properly installing the Motherwell Products Solo Luggage Rack.

ATTENTION INSTALLER (if other than the owner): Please forward this instruction sheet to the purchaser of this product as it contains valuable information necessary to the end user.
CAUTION: Start screwing carefully to avoid cross-threading.

  • FITMENT: Fits on 691S and 691T (Indian Chieftain, Springfield, Roadmaster, & Challenger)
  • MAX CAPACITY: 10 lbs
  • MATERIAL: 3/4” Tubular Steel, 12-gauge CR Steel
  • TECHNICAL SPECS: Fits MWL-691s & MWL-691T (MB/GB/CH)

PARTS INCLUDED

  • Luggage Rack
  • Hex Cap Screw
  • 4 SS MG Flat Washers

TOOLS REQUIRED:
7/16” Wrench or 11 pt. Wrench Kit 23 (included)

MWL Part #:
MWL-667, FAS-002, FAS-054

USE AND CARE

Wash your accessories with the same care you use when washing your motorcycle. Use mild soap and water. DO NOT use abrasive chemicals or cleaners. We recommend the use of non-abrasive automobile wax to polish our products. This will best maintain the appearance of the product and increase longevity.

WARNING: Never carry more than 10 lbs. on rack, and always secure cargo properly. Failure to do so can affect handling. Make sure neither cargo straps are loose and come in contact with moving parts, i.e., wheels, brakes, etc…

MOUNTING PROCEDURE

  1. Remove backrest from the bike if installed.
  2. Remove 4 existing bolts on the inside of the Sissybar side plates on Rack mounting block.
  3. Slide luggage rack from inside bottom backrest to align with existing bolt holes.
  4. Insert the 4 bolts provided and tighten until just snug, check rack is square, and adjust as needed, then tighten bolts fully.
  5. Reinstall bar on bike.

Great Rides Start With Motherwell
Motherwell Products USA, Inc
7074 Portal Way #140 Ferndale, WA 98248
Toll Free 877-703-7118
www.motherwellproducts.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals